You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
make and make upload okay, but no connection by martin2day » Tue, 2021-02-16 19:19 |
3 |
by CTSchorsch Wed, 2021-02-17 14:02 |
|
|
Problem with burned FETs and drivers after reconnect battery by CTSchorsch » Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
|
|
CAN defect? 4WD - CAN does not detect anymore... HELP! by MountainBen » Tue, 2021-02-02 04:04 |
3 |
by skyline1970 Fri, 2021-02-05 19:50 |
|
|
Differential steering with 2 VESC driving 2 BLDC in FOC mode with joystick by unimotion » Sat, 2018-11-10 18:59 |
10 |
by mikegrok Fri, 2021-01-29 21:40 |
|
|
Use different FET driver by Avin Raikwar » Fri, 2021-01-29 16:35 |
1 |
by skyline1970 Fri, 2021-01-29 21:00 |
|
|
Custom hardware flash problems by brightlightbeam » Mon, 2021-01-25 17:25 |
4 |
by brightlightbeam Thu, 2021-01-28 12:00 |
|
|
Robotics focussed mini VESC 6 derivative by StefanH » Tue, 2021-01-12 12:52 |
0 |
by StefanH Tue, 2021-01-12 12:52 |
|
|
Motors with known valid configurations by doctarr » Fri, 2021-01-01 14:28 |
4 |
by doctarr Sat, 2021-01-09 14:44 |
|
|
compatability assistance by NRGFPV » Mon, 2020-12-28 04:58 |
2 |
by NRGFPV Wed, 2020-12-30 08:46 |
|
|
No USB connection by Flepple » Sat, 2020-12-12 21:40 |
5 |
by vadicus Thu, 2020-12-17 21:06 |
|
|
Vesc faults when there is load by NIKTEN96 » Sat, 2020-12-12 23:30 |
1 |
by vadicus Mon, 2020-12-14 23:35 |
|
|
High Voltage ESC (HiVEsc) 150V 500A by e-biker » Thu, 2019-08-15 14:45 |
19 |
by jarrancho Fri, 2020-12-04 11:35 |
|
|
Motor Setup issues e-Snowboard by arosenthal » Fri, 2020-09-18 21:10 |
3 |
by etadada12 Sun, 2020-11-29 02:17 |
|
|
Is my custom motor inductance too low? by perpetum » Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
|
|
HELP set current settings for inverter by ka_ru » Wed, 2020-11-18 20:51 |
2 |
by ka_ru Mon, 2020-11-23 11:41 |
|
|
Hyper-V No "New" button in the action pane by Gheer » Tue, 2020-11-17 13:02 |
0 |
by Gheer Tue, 2020-11-17 13:02 |
|
|
MTVESC 6.12 DRV fault under load by rafchal@yahoo.com » Fri, 2020-11-06 00:21 |
0 |
by rafchal@yahoo.com Fri, 2020-11-06 00:21 |
|
|
Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss? by Gargazol » Tue, 2020-10-20 14:12 |
1 |
by TheFallen Tue, 2020-10-27 16:38 |
|
|
Problems with Maytech MTVESC6.12 by TheJohnson » Mon, 2020-10-19 04:50 |
2 |
by TheJohnson Wed, 2020-10-21 09:39 |
|
|
Trouble with FSESC75200 by Erik » Wed, 2020-10-07 19:09 |
0 |
by Erik Tue, 2020-10-13 15:07 |
|
|
Firmware flash on new born board by matrixgti » Thu, 2020-10-08 20:39 |
2 |
by TechAUmNu Tue, 2020-10-13 10:18 |
|
|
Phase voltage rise time by CTSchorsch » Wed, 2020-10-07 14:09 |
0 |
by CTSchorsch Wed, 2020-10-07 14:09 |
|
|
Custom board: R and L measurement problem! by JustClap » Thu, 2020-07-30 10:57 |
6 |
by nickw1881 Mon, 2020-10-05 20:18 |
|
|
Mini/micro/nano VESC solutions? by Cham » Mon, 2020-09-21 17:34 |
3 |
by Cham Thu, 2020-09-24 12:15 |
|
|
VESC clone smoked - help needed please by JoshuaGraham14 » Fri, 2020-09-11 00:14 |
1 |
by TheFallen Tue, 2020-09-22 10:34 |
Log in to post new content in the forum.
