You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
benjamin, New feature please by justinlinh » Sat, 2020-07-11 00:06 |
3 |
by justinlinh Sat, 2020-07-11 01:42 |
|
|
Is Vesc Tool App Hogging the Bluetooth? by Marctwo » Mon, 2020-07-06 11:10 |
1 |
by Marctwo Thu, 2020-07-09 08:29 |
|
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 » Mon, 2020-07-06 03:09 |
0 |
by bmwman91 Mon, 2020-07-06 03:21 |
|
|
Bug Report - Motor/App Data not saved to VESC by bb67 » Sun, 2020-06-21 10:26 |
1 |
by bb67 Sat, 2020-07-04 12:21 |
|
|
Max RPM by donrecardo » Thu, 2020-06-25 12:00 |
1 |
by Tibor Kalman Za... Mon, 2020-06-29 21:03 |
|
|
App Config disabled one side problem by timfame11 » Sat, 2020-06-27 00:26 |
0 |
by timfame11 Sun, 2020-06-28 05:21 |
|
|
Please remove bootloader update section from FW Tab by sunbeam » Sun, 2019-09-15 01:12 |
1 |
by TechAUmNu Sat, 2020-06-27 09:33 |
|
|
Bluetooth RX/TX by eastcoastkiter » Fri, 2019-06-28 19:02 |
5 |
by radler Sat, 2020-06-20 17:06 |
|
|
Dual Motor Setup not working via CAN Bus (solved) by acleon » Fri, 2020-06-19 00:03 |
0 |
by acleon Fri, 2020-06-19 16:33 |
|
|
VESC Tool Makes my remote unusable by IcecreamSamurai » Mon, 2020-06-15 01:49 |
0 |
by IcecreamSamurai Mon, 2020-06-15 01:49 |
|
|
Unrecognized USB port vesc tool 1.25 by geotoine » Fri, 2019-11-08 15:35 |
1 |
by bb67 Fri, 2020-06-12 18:10 |
|
|
How to select in VESC Tool the COM port of PC for USB connection to VESC6? by Heimfried » Mon, 2020-05-11 20:27 |
3 |
by Heimfried Wed, 2020-06-10 11:54 |
|
|
Detection for a drone outrunner 515 kV and 775 kV by MaksK » Thu, 2020-06-04 16:05 |
0 |
by MaksK Thu, 2020-06-04 16:05 |
|
|
[SOLVED] Compile vesc tool mobile apk by TZTZ » Mon, 2020-05-25 18:51 |
1 |
by TZTZ Mon, 2020-05-25 23:14 |
|
|
Input fields bug report by DerKrawallkeks » Thu, 2020-05-21 17:06 |
0 |
by DerKrawallkeks Thu, 2020-05-21 17:13 |
|
|
Can't find good parameters for FOC detection by Kabroc » Thu, 2020-04-30 16:28 |
0 |
by Kabroc Thu, 2020-04-30 16:28 |
|
|
Nrf connection error by vufmihai » Sat, 2020-04-25 22:00 |
0 |
by vufmihai Sat, 2020-04-25 22:00 |
|
|
Question about COMM_GET_IMU_DATA packet by rrzaripov » Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
|
|
Servo Control PPM by jonthie » Tue, 2020-01-28 15:04 |
2 |
by IanG Thu, 2020-04-16 11:42 |
|
|
foc detection params by stefann » Mon, 2020-04-13 00:07 |
0 |
by stefann Mon, 2020-04-13 00:28 |
|
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:03 |
0 |
by stefann Wed, 2020-04-08 23:03 |
|
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:02 |
0 |
by stefann Wed, 2020-04-08 23:02 |
|
|
FOC configuration when resistance is measured as R=0. by Roger Wolff » Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
|
|
VESC Tool Battery Settings for 5S Lipo by Bildoon » Sat, 2020-04-04 23:28 |
1 |
by Bildoon Mon, 2020-04-06 01:24 |
Log in to post new content in the forum.
