Hello people,
Im currently using VESC to control a motor that translates its rotatory motion into translational motion so I can move parts from left to right and vise versa.
I wonder why its seems that VESC limitates the total current to about 20A. There is no "current-barrier" in the settings.
Hi,
How can you adjust the throttle curve such that you get a small positive current at zero input of your ADC controller?
I tried to play with VESCtool setting myself and I searched the forums, but I can't find an answer to this question.
I thought about setting the ADC1 Min Voltage to a negative number, but VESCtool does not allow.
Any tips are much appreciated!
(I have a vesc6 with firmware 5.1 and am using Vesc Tool 2.06 for pc and android phone)
Hi , I am new in this world.
I have ordered a VESC 6 MkV from Trampa and downloaded the free Windows vesc_tool_3.00.exe to start understanding the possibilities.
When I run the vesc_tool_3.00.exe on my notebook, it start with a blank windows but after few seconds it close itself without messages .
The TRAMPA support says " it is when the PC is not powerful enough to run the tool ".
My question is now Is there any PC requirements tu run the Windows tool ?
Good morning, I'm using VESC 4.12 to run my 6354 flipsky BLDC motor. I'm participating in a competition where I'm required to display data on my user interface. I've some questions regarding the same.
(1.) How can I make my VESC work using UART on Arduino?
(2.) Will it be able to send data to the Arduino, as I'll be required to display it on my user interface. Looking forward to hearing from you all.
Looking forward to hearing from you
Regards
I recently had a VESC 60HD-T failure that I'm a bit perplexed over. I had run the automatic setup wizards is VESC Tool and for the most part seemed like no-load operation was working very smoothly. The only issue I had was that measured battery current (via current probe) was quite a bit higher than what the SW was reading -- I'm mentioning that here as I will go into further current-based issues later so there may be a link.
Hi All,
I am confused about the full brake button on VESC Tool. I know that it sets the duty cycle to 0. I am using FOC and when I press the full brake button I still read some non-zero e-rpm value. If the duty cycle is 0 then how do I read some non-zero erpm.
Also, how is that different from switching the system off. I know they are not the same thing but I do not what they actually mean.
Thank you in advance
Cheers
Apologies if this is a basic question, but I can't seem to find the answer anywhere.
I've got an FOC application. Under the FOC menu I have 'Encoder' chosen as 'Sensor Mode', but then under the Encoder tab the 'Sensorless ERPM' is set to 4000, which is lower than my min, so I believe that means it's running sensorless all the time?
My question is regarding the D and ω fields. I've tried using each of those for controlling my motor, and I've noticed some differences between them. Specifically:
Just got a VESC HD-60T yesterday and after following the set-up wizards in VESC Tool was able to get my motor spinning without too much trouble.
I don't have any remote control hardware (in my final application I'm planning on using CAN), so in the meantime I'm trying to do some motor testing purely over USB using the RPM and D settings at the bottom of the VESC Tool window to get the motor spinning at different speeds.
I have a Ninebot Max scooter. I replaced the ESC with a VSC. Is the throttle 3.3 or 5v? Is the brake 3.3 or 5v? I have a 13s6p battery. The app is asking me how many amp the batt is. Each cell or total pack? Also, I have a 12 LED light i want to hook up. There is 12v, gnd, and AUX. What is the AUX term for?
I have been trying for (no joke) like 14 hours to get my new Flipsky VESC working with my Esk8. I have followed the instructions to a T as far as I can tell. I cant find anyone who can help. I know for fact my battery and motor are good. If anyone is near Manchester NH I will pay you to come fix this or if someone is a whiz, I will screenshare with you and you can take control. PLEASE HELP. I am very frustrated and discouraged with this. Feel free to text me if you think you can help six oh three 5 oh 5 69 five9
