You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Benchmark regenerative braking by diggis on Fri, 2021-02-19 10:01 |
by diggis Fri, 2021-02-19 10:01 |
VESC Tool | ||
|
about Hall count (tacho value) problem by sirino on Wed, 2021-02-17 02:35 |
1 |
by sirino Fri, 2021-02-19 08:31 |
VESC Firmware | |
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas on Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
VESC Tool | |
|
VESC controlled by CAN by j.m on Wed, 2021-02-17 10:51 |
1 |
by TheFallen Fri, 2021-02-19 00:52 |
General discussion | |
|
how to delete pc install, struggling to get the mobile program to work :) by jon218white on Thu, 2021-02-18 20:47 |
1 |
by TheFallen Fri, 2021-02-19 00:31 |
General discussion | |
|
VESC 75/300 UART connections to microcontroller by tecnico.solarboat on Sun, 2021-02-14 17:53 |
6 |
by TheFallen Fri, 2021-02-19 00:17 |
VESC Original Hardware | |
|
Hoverboard motors not spinning when manually controlled, work when doing hall test etc. by VK2EVA on Fri, 2020-12-25 22:01 |
2 |
by ATHIVEL Thu, 2021-02-18 15:45 |
General discussion | |
|
VESC Response time and update rates by JimKazmer on Fri, 2021-02-12 04:14 |
3 |
by JimKazmer Thu, 2021-02-18 02:15 |
VESC Firmware | |
|
Control current PID from UART by Koxx on Wed, 2021-02-17 20:27 |
by Koxx Wed, 2021-02-17 20:27 |
VESC Firmware | ||
|
Using a VESC V4.12 for a machining lathe by Krampas on Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
|
PID Position Controller by IanG on Wed, 2020-03-25 03:05 |
5 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
|
Firware 5.2 by julitosanse on Wed, 2021-01-27 03:59 |
2 |
by zaporka Wed, 2021-02-17 16:42 |
VESC Development and Beta Testing | |
|
make and make upload okay, but no connection by martin2day on Tue, 2021-02-16 19:19 |
3 |
by CTSchorsch Wed, 2021-02-17 14:02 |
Third Party Hardware | |
|
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
|
UART CAN forwarding by frankus on Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
General discussion | |
|
Using vesc between many motors by EliProtiva on Tue, 2021-02-16 05:32 |
by EliProtiva Tue, 2021-02-16 05:32 |
General discussion | ||
|
advice on position control by feskarn on Mon, 2021-02-15 14:47 |
by feskarn Mon, 2021-02-15 14:47 |
General discussion | ||
|
Adding a Openloop COMM Comand by JulianT on Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
Feature Requests | |
|
Adding a Openloop COMM Comand by JulianT on Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
General discussion |
Pages
