You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
vesc hardware 4.12 by BasilBrushy on Fri, 2020-04-24 11:56 |
by BasilBrushy Fri, 2020-04-24 11:56 |
Third Party Hardware | ||
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
TMP100 I2C Sensor by CTSchorsch on Tue, 2020-04-21 15:55 |
by CTSchorsch Tue, 2020-04-21 15:55 |
VESC Firmware | ||
Print statements - Firmware by vitormhenrique on Sun, 2020-02-23 22:03 |
4 |
by Siverian Sun, 2020-04-19 22:10 |
VESC Firmware | |
Firmware Update = Quiet Motor? by worldmaverik on Sun, 2020-04-19 21:45 |
by worldmaverik Sun, 2020-04-19 21:45 |
General discussion | ||
Custom VESC4 hardware - disable Regen? by ben5243 on Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
General discussion | |
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
VESC Tool | |
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung on Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
General discussion | |
How to update firmware over CAN bus by andrii619 on Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
General discussion | |
No, BLDC is not dead. by Pimousse on Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
General discussion | |
4 vesc motors at once? by i-make-robots on Thu, 2020-04-16 02:17 |
1 |
by hexakopter Sat, 2020-04-18 12:20 |
General discussion | |
Newbie Help please, Longer run time? by Bildoon on Mon, 2020-04-06 02:00 |
1 |
by linsus Thu, 2020-04-16 14:18 |
General discussion | |
Servo Control PPM by jonthie on Tue, 2020-01-28 15:04 |
2 |
by IanG Thu, 2020-04-16 11:42 |
VESC Tool | |
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 03:27 |
by AllenFF Wed, 2020-04-15 03:27 |
General discussion | ||
rangeextender build - Vesc trying to fry itself by DIY_rangeextender on Tue, 2020-03-17 08:43 |
1 |
by bgdwiepp Wed, 2020-04-15 01:28 |
Third Party Hardware | |
Welding with the VESC by doomy1986 on Mon, 2020-04-13 14:38 |
by doomy1986 Mon, 2020-04-13 14:38 |
General discussion | ||
foc detection params by stefann on Mon, 2020-04-13 00:07 |
by stefann Mon, 2020-04-13 00:28 |
VESC Tool | ||
How to control a vesc controller without pulling electric wires on a bike? by peignier jacques on Sat, 2020-04-11 09:20 |
by peignier jacques Sat, 2020-04-11 09:21 |
Feature Requests | ||
Using STM32F407 for a custom board by kapek on Mon, 2020-04-06 04:16 |
2 |
by vadicus Fri, 2020-04-10 06:31 |
General discussion | |
help with vesc real time data trouble shooting by stefann on Wed, 2020-04-08 23:03 |
by stefann Wed, 2020-04-08 23:03 |
VESC Tool |