You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
HW 4.12 Change low voltage cutoff by subodh.malgonde on Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
VESC Original Hardware | |
|
Setting up Flipsky 4.2 Dual and VX2 remote FW issues - Please help by Rashid1992 on Wed, 2020-12-23 17:13 |
7 |
by MartyMcFlyFord Mon, 2022-05-23 14:44 |
VESC Firmware | |
|
CAN bus protocol upgrade thoughts by Pimousse on Fri, 2020-03-20 15:37 |
7 |
by renaudbarbier Sat, 2024-04-27 07:53 |
VESC Development and Beta Testing | |
|
Motor jitters and skips poles, but only in one direction by L0laapk3 on Mon, 2022-09-19 21:32 |
7 |
by frank Wed, 2022-09-21 09:07 |
General discussion | |
|
Welcome by frank on Fri, 2017-06-02 16:31 |
7 |
by sebaszz Fri, 2017-06-09 22:36 |
VESC6 Beta | |
|
coms port bluetooth and switch and adc ? by badger1666 on Tue, 2017-12-12 17:20 |
7 |
by Ampit Fri, 2023-12-22 13:34 |
General discussion | |
|
Sensorless ERPM confusion and cogging in FOC by Addy on Mon, 2018-05-14 22:38 |
7 |
by bayetan Sun, 2023-06-04 17:19 |
General discussion | |
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze on Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
General discussion | |
|
Probably first dead VESC SIX by Squad on Tue, 2017-06-27 14:00 |
8 |
by frank Thu, 2017-08-17 22:31 |
VESC6 Beta | |
|
Flipsky HC 200A VESC programming to eFoil motor by tylerclark on Wed, 2020-03-11 05:52 |
8 |
by okarbon Tue, 2021-02-23 13:19 |
VESC Firmware | |
|
VESC with propeller, not reaching max performance by ogent on Tue, 2022-02-01 16:31 |
8 |
by ogent Thu, 2022-02-03 14:54 |
VESC Firmware | |
|
No connection with vesc by Matthieu van Ra... on Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
General discussion | |
|
VESC as Generator - Low Output at High Brake Current? by hoeken on Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
General discussion | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion | |
|
No UART Output on VESC6 MKIV by uwala on Sun, 2020-10-25 12:13 |
8 |
by tsm Tue, 2021-12-21 15:20 |
VESC Development and Beta Testing | |
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL on Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
VESC Tool | |
|
Communication with Vesc Tools by faheemift on Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
General discussion | |
|
How to fix VESC killed by over current in serial comm? by 8bit on Sun, 2021-05-16 04:02 |
8 |
by vadicus Fri, 2023-01-13 19:15 |
Third Party Hardware | |
|
Alien Power Systems Hall Sensors with VESC6 by lazerusrm on Tue, 2018-03-13 02:52 |
8 |
by faulknernolan Tue, 2022-07-05 11:36 |
General discussion | |
|
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool |
Pages
