You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
ERPM Limit Update Over CAN by josh on Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
Feature Requests | |
|
UART write read arduino by matiller on Sat, 2019-06-01 20:18 |
by matiller Sat, 2019-06-01 20:18 |
VESC Tool | ||
|
Arduino UART communication HW4.10 FW3.56 by joseguerra on Wed, 2019-05-22 13:01 |
1 |
by Pimousse Thu, 2019-05-30 17:23 |
General discussion | |
|
ADC Positive and Negative Ramping Time - not working by Astropower on Tue, 2019-05-28 22:41 |
by Astropower Tue, 2019-05-28 22:41 |
VESC Tool | ||
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl on Tue, 2019-05-28 14:48 |
by Jackl Tue, 2019-05-28 14:48 |
VESC Original Hardware | ||
|
half speed on FOC vs BLDC by ever.summer on Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
General discussion | |
|
Strange behaviour when controlling RPM by MrMonk3y on Wed, 2019-05-08 14:29 |
1 |
by cnd Mon, 2019-05-27 08:41 |
General discussion | |
|
Servomotor control with VESC6 by Humberto Estrada on Wed, 2019-05-22 16:15 |
by Humberto Estrada Wed, 2019-05-22 16:15 |
VESC Original Hardware | ||
|
Reading tachometer over can bus by kimpet on Sun, 2019-05-12 22:24 |
5 |
by benjamin Sun, 2019-05-19 14:58 |
General discussion | |
|
Notified of new version of firmware, can't DL it... by kchxaz on Sun, 2019-05-19 03:28 |
1 |
by hexakopter Sun, 2019-05-19 13:26 |
VESC Firmware | |
|
FOC Detection works but BLDC detection fails by gv260ea on Sun, 2019-05-19 04:15 |
by gv260ea Sun, 2019-05-19 04:15 |
General discussion | ||
|
DC-Link Capacitor Selection by rushi95 on Sat, 2019-05-18 12:15 |
1 |
by hexakopter Sat, 2019-05-18 12:39 |
General discussion | |
|
E-Bike Throttle connect with Regenerative Braking by E-Toxx on Sat, 2017-09-09 09:38 |
4 |
by Jacki Villis Thu, 2019-05-16 14:43 |
General discussion | |
|
No firmware listed, after DRV repair by anymorez on Thu, 2019-04-18 14:24 |
1 |
by Dillon Thu, 2019-05-16 01:35 |
VESC Firmware | |
|
Is COMM_GET_VALUES working on 3.56 fw 410 ? by cnd on Tue, 2019-05-14 17:10 |
by cnd Tue, 2019-05-14 17:10 |
VESC Firmware | ||
|
Troubleshooting Newborn VESC by vadicus on Tue, 2019-04-09 02:13 |
3 |
by vadicus Tue, 2019-05-14 02:06 |
Third Party Hardware | |
|
Easy way to save VESC parameters before updating FW with VESC tool ? by unimotion on Sat, 2019-05-11 19:15 |
1 |
by unimotion Sun, 2019-05-12 16:42 |
VESC Firmware | |
|
100k NTC by CTSchorsch on Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
General discussion | |
|
VESC Tool Error by Geir Henriksen on Fri, 2019-05-10 14:55 |
1 |
by Geir Henriksen Fri, 2019-05-10 15:18 |
VESC Tool | |
|
Problem with BLDC and Firmware 3.55 by NPH22 on Thu, 2019-05-02 19:21 |
4 |
by paltatech Fri, 2019-05-10 06:23 |
VESC Firmware |
Pages
