You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen on Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
VESC Tool | |
|
High rpm issue kde3520xf by magnus.w on Fri, 2019-04-26 12:46 |
1 |
by magnus.w Sat, 2019-05-04 12:33 |
General discussion | |
|
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
|
Switchign frequency issue? by Maxid on Thu, 2020-12-03 11:47 |
by Maxid Thu, 2020-12-03 11:47 |
VESC Firmware | ||
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings on Thu, 2022-06-23 23:43 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
General discussion | ||
|
Vesc gps control by Erik on Thu, 2019-11-14 20:38 |
by Erik Thu, 2019-11-14 20:38 |
General discussion | ||
|
Any way to increase detection time? by VapeGod on Wed, 2023-01-25 05:58 |
by VapeGod Wed, 2023-01-25 05:58 |
General discussion | ||
|
Motor starting while flasing firmware by RSR on Sun, 2017-09-17 15:31 |
by RSR Sun, 2017-09-17 15:31 |
VESC Tool | ||
|
Throttle Input reading not changing by niko_la on Fri, 2022-07-22 02:40 |
by niko_la Fri, 2022-07-22 02:40 |
VESC Tool | ||
|
VESC HD60 schematic by junho912 on Wed, 2024-04-03 10:55 |
by junho912 Wed, 2024-04-03 10:55 |
VESC Original Hardware | ||
|
VESC WAND by vitormhenrique on Sun, 2020-02-16 19:04 |
by vitormhenrique Sun, 2020-02-16 19:26 |
VESC Original Hardware | ||
|
Incorrect speed too high by Michele84 on Wed, 2021-07-21 15:48 |
by Michele84 Wed, 2021-07-21 15:48 |
VESC Tool | ||
|
connecting vesc tool with Prototipo by Govert on Thu, 2020-07-02 19:43 |
by Govert Thu, 2020-07-02 19:43 |
General discussion | ||
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl on Tue, 2019-05-28 14:48 |
by Jackl Tue, 2019-05-28 14:48 |
VESC Original Hardware | ||
|
Extremely slow FW update (Vesc Tool 2.2) by fender90 on Mon, 2020-02-03 19:26 |
by fender90 Wed, 2020-02-05 05:22 |
VESC Tool | ||
|
Bluetooth module in VESC 75/300 by Hermann Schnaeuzle on Fri, 2022-04-22 17:55 |
by Hermann Schnaeuzle Fri, 2022-04-22 17:55 |
General discussion | ||
|
Vesc_tool OVER_TEMP_FET by XIII on Thu, 2018-01-11 17:26 |
by XIII Thu, 2018-01-11 17:26 |
VESC Tool | ||
|
Problem with BLDC motor direction and code starting sequence. by masifsr on Fri, 2022-04-15 12:37 |
by masifsr Fri, 2022-04-15 12:37 |
VESC Firmware | ||
|
I need VESC Tool Version 1.13, please. by Astropower on Sun, 2019-09-08 18:22 |
by Astropower Sun, 2019-09-08 18:22 |
VESC Tool | ||
|
display readings by FatsoBatso on Wed, 2021-02-24 18:01 |
by FatsoBatso Wed, 2021-02-24 18:01 |
General discussion |
Pages
