You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
PID Speed Control code....for NRF by Dimitri on Tue, 2017-10-03 07:16 |
by Dimitri Tue, 2017-10-03 07:18 |
VESC Firmware | ||
I need a minor change to my firmware by cdw3423vesc on Sat, 2018-11-17 00:55 |
by cdw3423vesc Sat, 2018-11-17 00:55 |
VESC Firmware | ||
Wrong Motor/Battery Amps Measured? by King John on Thu, 2020-01-23 04:51 |
by King John Thu, 2020-01-23 04:51 |
Third Party Hardware | ||
vesc canbus control PPM by JiaheXu on Thu, 2023-04-13 20:17 |
by JiaheXu Thu, 2023-04-13 20:17 |
General discussion | ||
Unity HFI but I can only configure one motor by ZQuimson on Mon, 2021-06-07 20:02 |
by ZQuimson Mon, 2021-06-07 20:02 |
General discussion | ||
How do I disable brake? by moo10032 on Tue, 2021-02-23 08:09 |
by moo10032 Tue, 2021-02-23 08:10 |
VESC Tool | ||
Vesc to Uart (Nextion display) by g1tana on Mon, 2019-08-19 15:29 |
by g1tana Mon, 2019-08-19 15:30 |
General discussion | ||
Welding with the VESC by doomy1986 on Mon, 2020-04-13 14:38 |
by doomy1986 Mon, 2020-04-13 14:38 |
General discussion | ||
what do you guys think about this "curr_samp_volt "? by jem on Thu, 2019-08-08 14:45 |
by jem Thu, 2019-08-08 14:45 |
VESC Firmware | ||
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
Switchign frequency issue? by Maxid on Thu, 2020-12-03 11:47 |
by Maxid Thu, 2020-12-03 11:47 |
VESC Firmware | ||
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings on Thu, 2022-06-23 23:43 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
General discussion | ||
Vesc gps control by Erik on Thu, 2019-11-14 20:38 |
by Erik Thu, 2019-11-14 20:38 |
General discussion | ||
Any way to increase detection time? by VapeGod on Wed, 2023-01-25 05:58 |
by VapeGod Wed, 2023-01-25 05:58 |
General discussion | ||
Throttle Input reading not changing by niko_la on Fri, 2022-07-22 02:40 |
by niko_la Fri, 2022-07-22 02:40 |
VESC Tool | ||
VESC WAND by vitormhenrique on Sun, 2020-02-16 19:04 |
by vitormhenrique Sun, 2020-02-16 19:26 |
VESC Original Hardware | ||
Incorrect speed too high by Michele84 on Wed, 2021-07-21 15:48 |
by Michele84 Wed, 2021-07-21 15:48 |
VESC Tool | ||
I dont want that my motorwheel works like generator by Vi1 on Sat, 2024-04-27 14:13 |
by Vi1 Sat, 2024-04-27 14:13 |
VESC Tool | ||
Write Motor Configuration - not working by acherpil on Tue, 2018-12-04 10:23 |
by acherpil Tue, 2018-12-04 16:43 |
VESC Firmware | ||
connecting vesc tool with Prototipo by Govert on Thu, 2020-07-02 19:43 |
by Govert Thu, 2020-07-02 19:43 |
General discussion |