You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto on Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
VESC Original Hardware | |
|
Can't ajust braking torgue with Plettenberg Predator 30/8 by VescBuilder on Sun, 2017-11-12 16:13 |
6 |
by benjamin Thu, 2017-11-23 09:38 |
Third Party Hardware | |
|
Upgraded from 2.18 to 3.33 - Lost Telemetry by ervinelin on Thu, 2017-11-23 09:09 |
1 |
by Pedrodemio Thu, 2017-11-23 17:03 |
VESC Firmware | |
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar on Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
General discussion | |
|
Initial Setup wizard fails, HW 4.10 by wdaehn on Tue, 2017-09-12 18:47 |
7 |
by wdaehn Wed, 2017-11-29 14:21 |
VESC Tool | |
|
Servo Motor position control by wdaehn on Wed, 2017-11-29 21:45 |
by wdaehn Wed, 2017-11-29 21:45 |
Feature Requests | ||
|
RPM measurement. by Roger Wolff on Wed, 2017-11-29 16:48 |
2 |
by Roger Wolff Fri, 2017-12-01 06:25 |
General discussion | |
|
bugreport. Scale useless by Roger Wolff on Wed, 2017-11-29 12:24 |
1 |
by Svenska Svenson Mon, 2017-12-04 07:56 |
VESC Tool | |
|
Hub Motor Remote Control by bf01 on Tue, 2017-11-14 16:04 |
3 |
by frank Wed, 2017-12-06 23:41 |
General discussion | |
|
Minimum speed by Davideo on Sat, 2017-10-21 17:40 |
7 |
by Davideo Thu, 2017-12-07 00:18 |
General discussion | |
|
Driving the FETs.... by Roger Wolff on Sat, 2017-10-21 16:37 |
17 |
by Roger Wolff Mon, 2017-12-11 20:55 |
Third Party Hardware | |
|
MOSFET driver delay compensation by e-biker on Sun, 2017-12-10 16:21 |
2 |
by e-biker Tue, 2017-12-12 09:41 |
General discussion | |
|
trampa by badger1666 on Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
General discussion | |
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 on Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
VESC Firmware | |
|
Two Motors on same Shaft by Giga93 on Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
General discussion | |
|
Motor shaft machining advices are welcome! by ThierryGTLTS on Tue, 2017-11-14 17:40 |
5 |
by William Yates Mon, 2017-12-18 18:22 |
The VESC-Project | |
|
VESC hardware schematics by cromoly on Tue, 2017-11-28 04:44 |
4 |
by ThierryGTLTS Tue, 2017-12-19 14:03 |
VESC Original Hardware | |
|
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter on Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
VESC Firmware | |
|
Motor detection failed/ 0 faults by jnweb29 on Sat, 2017-12-23 21:07 |
by jnweb29 Sat, 2017-12-23 21:07 |
VESC Tool |
Pages
