You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Been at it for like 14 hours... HALP by mnchvgs79 on Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
VESC Tool | |
|
Overvoltage Error during setup by arranto12 on Mon, 2021-11-08 23:22 |
4 |
by electricfox Tue, 2025-02-04 19:28 |
General discussion | |
|
C Type USB and Power Delivery 3.1 by Rarikao on Fri, 2023-04-21 08:51 |
4 |
by vadicus Fri, 2023-04-28 05:30 |
Feature Requests | |
|
outdated vesc firmware troubles by alybruce on Sun, 2018-10-28 13:06 |
4 |
by Jose Dominguez Fri, 2020-09-04 00:58 |
VESC Firmware | |
|
No USB with latest VESC FW on 4.12 hardware by chris1seto on Thu, 2019-04-04 04:01 |
4 |
by dp Wed, 2020-12-02 13:01 |
VESC Firmware | |
|
VESC not responding to Controller by jcab on Thu, 2018-03-08 21:51 |
4 |
by Popeye Mon, 2019-06-10 23:59 |
VESC Firmware | |
|
Available connectors by nopf on Wed, 2024-09-18 09:33 |
4 |
by tobiokanobi Sun, 2024-10-20 17:38 |
VESC Original Hardware | |
|
Set RPM - reverse direction over CAN-Bus by 65273 on Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
General discussion | |
|
Hall sensor not working by Stupidspencer on Sat, 2019-12-28 20:29 |
4 |
by BeliaEllet Wed, 2021-03-31 17:55 |
VESC Original Hardware | |
|
Connect vesc tool with ANT BMS by Vdca on Sun, 2024-01-14 23:15 |
4 |
by Timo Wedel Sat, 2024-07-27 14:41 |
VESC Tool | |
|
Using vesc for Position and driving my BB8 Robot by Quicksilverstar on Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
General discussion | |
|
Reverse button configuration by ElectroToshka on Thu, 2022-06-23 11:09 |
4 |
by frank Fri, 2022-06-24 10:42 |
Third Party Hardware | |
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy on Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
General discussion | |
|
firmware V6.06 vs VESC tool V6.05 by shuang on Thu, 2024-12-05 06:49 |
4 |
by F65 Thu, 2026-01-22 16:46 |
VESC Firmware | |
|
DRV8301 Gate Drive value in Control Register by shaman on Thu, 2019-10-17 04:22 |
4 |
by Rovimo Thu, 2021-01-28 11:14 |
VESC Firmware | |
|
Power button works only as turn ON button, but not working as turn OFF by zmei116 on Tue, 2020-05-26 18:52 |
4 |
by electricfox Sat, 2024-03-09 18:57 |
VESC Original Hardware | |
|
How to increase startup torque? by Enak on Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
VESC Tool | |
|
Can't connect to VESC's? Linux, need help? by ex-Gooserider on Wed, 2020-08-12 04:38 |
4 |
by ex-Gooserider Wed, 2020-08-19 01:39 |
General discussion | |
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston on Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
General discussion | |
|
Hooking up two or more motor drivers to the same MCU by darkclaude on Thu, 2019-06-20 10:02 |
4 |
by skyline1970 Wed, 2019-07-31 13:53 |
Third Party Hardware |
Pages
