You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho on Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
General discussion | |
|
paltatech v0.2 HW not supported in latest firmware? by samuelis01 on Sun, 2019-10-27 22:52 |
by samuelis01 Sun, 2019-10-27 22:52 |
VESC Firmware | ||
|
Unable to flash firmware to VESC using OpenOCD by Bayne on Fri, 2019-10-25 02:34 |
by Bayne Fri, 2019-10-25 02:35 |
VESC Firmware | ||
|
Using the parameter editor by dqt boi on Thu, 2019-10-24 23:31 |
by dqt boi Thu, 2019-10-24 23:31 |
General discussion | ||
|
Any issues with the DRV8323? by shaman on Thu, 2019-10-24 21:50 |
by shaman Thu, 2019-10-24 21:50 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
version of Vesc Tool for Flipsky 6.6 by Robert Adkins on Sun, 2019-09-29 18:13 |
3 |
by frank Wed, 2019-10-23 09:35 |
VESC Tool | |
|
EBESC 6.1 Remote wont connect and cant get past the error code port not recognized by flashg69777 on Tue, 2019-10-22 02:01 |
1 |
by frank Tue, 2019-10-22 11:13 |
Third Party Hardware | |
|
safety switch by Ralph Luckwaldt on Mon, 2019-10-21 13:15 |
1 |
by frank Mon, 2019-10-21 20:58 |
Feature Requests | |
|
Pulling fault codes without USB by shaman on Fri, 2019-10-18 15:13 |
5 |
by shaman Sun, 2019-10-20 22:54 |
General discussion | |
|
IGBT Vesc FOC not working by ziumus on Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
Third Party Hardware | |
|
VESC as a 3 phase inverter to power a grid model by pf26 on Tue, 2019-03-19 20:54 |
5 |
by shaman Fri, 2019-10-18 15:06 |
General discussion | |
|
DC to AC pure-sine inverter mode by shaman on Fri, 2019-10-18 15:06 |
by shaman Fri, 2019-10-18 15:06 |
Feature Requests | ||
|
New to electronics, I have some questions about monitoring RPM by Trent on Fri, 2019-10-18 08:01 |
1 |
by frank Fri, 2019-10-18 13:34 |
General discussion | |
|
Driving two motors with 75/300 by cmarc on Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
VESC Original Hardware | |
|
SpaceVESC, a modular small VESC by SpaceVESCproject on Wed, 2019-10-02 21:35 |
2 |
by frank Thu, 2019-10-17 11:47 |
Third Party Hardware | |
|
Much lower torque in foc compared to bldc mode by asaf123098 on Sat, 2019-10-12 18:26 |
1 |
by frank Thu, 2019-10-17 11:15 |
General discussion | |
|
GPDrive as AC current source by jdn2 on Tue, 2019-10-15 14:22 |
1 |
by frank Thu, 2019-10-17 11:14 |
General discussion | |
|
Connecting the VESC6 plus with servo wires by GreenPenguin on Wed, 2019-10-16 15:39 |
1 |
by frank Thu, 2019-10-17 11:11 |
General discussion | |
|
New Control Algorithm for asynchronous machines by ajpina on Sun, 2019-05-19 22:13 |
4 |
by Henque19 Wed, 2019-10-16 23:29 |
VESC Firmware |
Pages
