You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 on Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
General discussion | |
|
Vesc with ROS over can bus by meilutisr on Fri, 2021-07-09 18:29 |
1 |
by hiqsol Tue, 2022-10-25 14:23 |
General discussion | |
|
Dual motor fishing boat by Snabelost on Mon, 2022-10-17 02:41 |
1 |
by canoeman Tue, 2022-10-25 15:11 |
Projects incorporating VESC technology | |
|
Aircraft Auxiliary Power Unit starter by Shaftdriver on Mon, 2022-10-10 13:10 |
4 |
by velolac Tue, 2022-10-25 20:38 |
Projects incorporating VESC technology | |
|
How to use an IMU and a PPM remote parallel by Gos1 on Tue, 2022-10-25 15:28 |
by Gos1 Wed, 2022-10-26 10:57 |
General discussion | ||
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
Issue with VESC I/O on donkey car by baluja on Fri, 2022-10-28 02:56 |
by baluja Fri, 2022-10-28 02:56 |
General discussion | ||
|
Porting VESC to STML4 by Vince_1618 on Fri, 2022-10-28 14:01 |
by Vince_1618 Fri, 2022-10-28 14:01 |
General discussion | ||
|
Is this kogging and jitter in low rpms expected? by Snabelost on Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
General discussion | |
|
Inquiry about Incremental and Absolute Encoders in VESC for Robotics by sivanhere on Fri, 2022-10-28 21:02 |
by sivanhere Fri, 2022-10-28 21:02 |
General discussion | ||
|
use SWDIO and SWCLK as normal GPIO ? by lqbweb on Mon, 2022-08-01 00:30 |
1 |
by snovotill Sat, 2022-10-29 18:28 |
VESC Development and Beta Testing | |
|
Wow wow by st0r on Sat, 2022-05-07 21:45 |
2 |
by Hansherrman Sun, 2022-10-30 01:40 |
General discussion | |
|
Current controller issue - Glitches at low current, low RPM by GijsB on Sun, 2022-10-30 12:59 |
1 |
by GijsB Sun, 2022-10-30 15:37 |
General discussion | |
|
Encoder position resetting to 0° by Michelle90 on Tue, 2022-10-25 18:55 |
1 |
by GijsB Sun, 2022-10-30 20:17 |
General discussion | |
|
Modified version of mini4,during motor detection，fault_code_drv-11 was reported by qdxiatao on Mon, 2022-10-31 07:42 |
by qdxiatao Mon, 2022-10-31 07:42 |
Third Party Hardware | ||
|
ADC throttle lock. by Billy_Wiz on Mon, 2022-10-31 00:57 |
1 |
by vadicus Mon, 2022-10-31 19:51 |
General discussion | |
|
Unable to turn on Smart Reverse by EBTEAM on Wed, 2022-11-02 08:35 |
1 |
by EBTEAM Wed, 2022-11-02 12:58 |
General discussion | |
|
VESC Tool Reporting RPM Different from Scope by bayetan on Wed, 2022-11-02 15:39 |
by bayetan Wed, 2022-11-02 15:39 |
VESC Firmware | ||
|
[solved] Where the motor configuration signature is from? by Beren on Thu, 2021-06-17 20:55 |
5 |
by rafeh1 Mon, 2022-11-07 00:45 |
VESC Development and Beta Testing | |
|
Forum GUI by parasole on Fri, 2017-11-10 09:25 |
1 |
by VJPANDI Thu, 2022-11-10 15:07 |
General discussion |
Pages
