You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Accidentally Bricked MakerX Go-Foc D60 by masong on Mon, 2023-04-24 07:41 |
by masong Tue, 2023-04-25 03:20 |
VESC Firmware | ||
|
EBike Bafang M500 mide drive motor: VESC + DIY ESP32 board running Pyhton firmware by yes_wecangogreen on Wed, 2023-04-12 00:43 |
by yes_wecangogreen Tue, 2023-04-25 02:04 |
Projects incorporating VESC technology | ||
|
despin platform by wjpremerlani on Fri, 2023-03-31 19:54 |
by wjpremerlani Mon, 2023-04-24 15:38 |
Projects incorporating VESC technology | ||
|
Maytech 100a ESC by NOldfield on Sat, 2023-04-22 08:51 |
by NOldfield Mon, 2023-04-24 15:32 |
Third Party Hardware | ||
|
VESC TOOL Mobile over OTG by xvatriusx on Sat, 2022-08-13 04:25 |
1 |
by besenyeim Mon, 2023-04-24 12:26 |
Feature Requests | |
|
Vesc for 5000kW QS 205 Hub Motor ebike by Amiran on Fri, 2019-09-27 15:52 |
10 |
by vadicus Sun, 2023-04-23 01:23 |
General discussion | |
|
Trapezoidal Trajectory/Position Control by wewa on Sun, 2018-09-23 11:33 |
4 |
by ncbanse Thu, 2023-04-20 21:26 |
Feature Requests | |
|
Can't get Dual drive/CAN bus working by Xadiant on Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
VESC Tool | |
|
VESC6 with DRV8320 by cromoly on Wed, 2023-04-19 02:40 |
by cromoly Wed, 2023-04-19 02:40 |
General discussion | ||
|
Throttle reworking for DPVs by badwiz on Sun, 2023-04-16 23:53 |
by badwiz Sun, 2023-04-16 23:53 |
VESC Firmware | ||
|
How does controlling two different motors over CAN bus really work? by oangelo on Sat, 2023-04-15 20:05 |
by oangelo Sat, 2023-04-15 20:05 |
General discussion | ||
|
HFI Mode Hoverboard Hub Motor by JulianT on Wed, 2023-04-12 19:16 |
by JulianT Sat, 2023-04-15 11:09 |
General discussion | ||
|
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D on Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
General discussion | |
|
How to adjust ADC1 parameters to adjust the speed (not working) by player107 on Fri, 2023-04-14 13:46 |
by player107 Fri, 2023-04-14 13:46 |
VESC Tool | ||
|
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant on Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
General discussion | |
|
vesc canbus control PPM by JiaheXu on Thu, 2023-04-13 20:17 |
by JiaheXu Thu, 2023-04-13 20:17 |
General discussion | ||
|
Position Limits w/ BDC and ABI Encoder by gokulswami on Thu, 2023-04-13 10:43 |
by gokulswami Thu, 2023-04-13 10:43 |
General discussion | ||
|
VESC as Generator - Low Output at High Brake Current? by hoeken on Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
General discussion | |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 on Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
General discussion |
Pages
