You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Error on log-file recording: Could not get Positioning Working by hpb66 on Mon, 2022-05-23 08:23 |
by hpb66 Mon, 2022-05-23 08:23 |
VESC Tool | ||
|
Error message by DAVCRO on Thu, 2023-03-09 17:15 |
1 |
by Gos1 Wed, 2023-07-05 13:17 |
Projects incorporating VESC technology | |
|
error firmware BMS by Sebastiangeitne... on Mon, 2022-08-15 21:36 |
1 |
by Sebastiangeitne... Thu, 2022-08-18 12:26 |
VESC Firmware | |
|
Error code 6 by PatWhite32 on Mon, 2023-06-19 23:15 |
by PatWhite32 Mon, 2023-06-19 23:15 |
General discussion | ||
|
Error 500 on older private messages by TechAUmNu on Wed, 2018-05-09 23:15 |
3 |
by Roger Wolff Mon, 2018-05-14 10:06 |
General discussion | |
|
Erratic braking on vesc using large hub motor. by jtechbop on Sun, 2021-09-19 06:54 |
2 |
by jtechbop Tue, 2021-10-19 20:59 |
General discussion | |
|
ERPM, the RPM on the motor does not change by hopeingod on Fri, 2024-05-10 11:15 |
1 |
by electricfox Fri, 2024-05-10 22:11 |
VESC Tool | |
|
ERPM to Rpm by faheemift on Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
General discussion | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
ERPM scaling / Maximum motor speed / RPM by Azza on Tue, 2019-09-03 17:16 |
1 |
by Azza Fri, 2019-09-06 18:20 |
VESC Tool | |
|
Erpm output via pwm by Flyingtux on Tue, 2021-09-14 20:34 |
2 |
by lurch Fri, 2021-10-29 14:09 |
General discussion | |
|
eRPM limited to 40600 or so on 6.6 by Dan Slanker on Fri, 2021-04-16 01:22 |
4 |
by TechAUmNu Mon, 2021-04-19 11:10 |
General discussion | |
|
ERPM Limit Update Over CAN by josh on Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
Feature Requests | |
|
Erpm / torque setting with remote control, Vesc wand by Lasse on Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
VESC Tool | |
|
Ericson 41 with electric motor driven by FS 75200 by Svein Utne on Tue, 2023-03-07 09:12 |
4 |
by Svein Utne Sun, 2023-03-12 06:49 |
Projects incorporating VESC technology | |
|
ennoid bms by roqm on Fri, 2020-10-30 18:22 |
by roqm Fri, 2020-10-30 18:22 |
VESC Tool | ||
|
Enhance sensorless FOC using phase vsense? by lizardmech on Tue, 2018-02-27 17:39 |
5 |
by lizardmech Wed, 2018-02-28 14:36 |
Feature Requests | |
|
Enhance position and rpm control interface / protocol by brushlessjoe on Wed, 2019-03-20 21:54 |
by brushlessjoe Wed, 2019-03-20 21:54 |
Feature Requests | ||
|
enertionboard focbox : is vesc_tool safe to use? by fourchette on Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
General discussion | |
|
Enertion FOCbox question by island bound trading on Sun, 2021-01-31 15:34 |
2 |
by s0313045 Fri, 2021-02-05 03:54 |
General discussion |
Pages
