You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
MICRO Module by F4metz on Sat, 2019-03-02 15:10 |
3 |
by chuttney1 Sun, 2019-03-03 18:54 |
Third Party Hardware | |
|
SPI encoder on MIN4 by john on Wed, 2018-11-14 11:31 |
1 |
by F4metz Sat, 2019-03-02 14:18 |
Third Party Hardware | |
|
When I mount the propeller on the motor ,I get a new promblem by moto_guy on Sat, 2019-03-02 05:16 |
by moto_guy Sat, 2019-03-02 05:16 |
General discussion | ||
|
Gate driver by RSR on Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
Third Party Hardware | |
|
Flipsky6.6 usb not detected by krom68 on Sat, 2019-02-23 10:21 |
by krom68 Wed, 2019-02-27 19:43 |
General discussion | ||
|
Flipsky6.6 usb not detected by krom68 on Sat, 2019-02-23 10:21 |
by krom68 Wed, 2019-02-27 19:43 |
Third Party Hardware | ||
|
HIGH Voltage (350v-450v) VESC by athlon on Sun, 2018-11-25 18:34 |
7 |
by thewho Tue, 2019-02-26 12:38 |
Third Party Hardware | |
|
Combat Robot Mods by BrianNave on Sun, 2019-02-24 17:03 |
by BrianNave Sun, 2019-02-24 17:03 |
Feature Requests | ||
|
VESC 4.12 problems with FW newer then 3.10 by muchtete on Tue, 2019-01-29 18:37 |
2 |
by GunnarW Sun, 2019-02-24 11:53 |
VESC Firmware | |
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy on Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
General discussion | |
|
Allow braking to override negative ramping time by Paul15578 on Wed, 2018-01-24 06:20 |
5 |
by benjamin Sat, 2019-02-23 10:14 |
Feature Requests | |
|
Inductance (L) measurement by rahmaev_a_o on Tue, 2018-08-07 10:10 |
4 |
by benjamin Sat, 2019-02-23 10:11 |
VESC Original Hardware | |
|
Current sensor and commanded current by galp on Fri, 2019-02-22 23:08 |
by galp Fri, 2019-02-22 23:08 |
General discussion | ||
|
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
|
VESC on DIY CNC router by tbartoletta on Wed, 2019-02-20 03:00 |
5 |
by GunnarW Thu, 2019-02-21 16:44 |
General discussion | |
|
setting up development environment for android by jaghori.sasan on Wed, 2019-02-20 14:59 |
by jaghori.sasan Wed, 2019-02-20 14:59 |
VESC Tool | ||
|
Paypal alternative by sam.vanratt on Sat, 2019-01-05 22:03 |
5 |
by benjamin Mon, 2019-02-18 20:11 |
The VESC-Project | |
|
Flipsky nrf51288 by Idoff on Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
VESC Tool | |
|
VESC Questions from the newbie by mendez on Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
General discussion | |
|
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 on Sun, 2019-02-17 19:20 |
by Syl2078 Sun, 2019-02-17 19:20 |
General discussion |
Pages
