You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
4wd rover using hub-motors by mhyer on Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
General discussion | |
|
Is my custom motor inductance too low? by perpetum on Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
Third Party Hardware | |
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn on Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
VESC Firmware | |
|
Vesc Tool not opening on windows computer by maccert on Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
VESC Tool | |
|
brake switch/brake regen question by smallbikefun on Sat, 2024-04-06 01:48 |
2 |
by smallbikefun Sun, 2024-04-14 22:08 |
VESC Tool | |
|
Gyro/Accel utilisation for built in Alarm ?! :D by yoodog on Tue, 2021-03-30 00:48 |
2 |
by yoodog Tue, 2021-03-30 01:07 |
General discussion | |
|
Dual Vesc6 setup: Vesc with nrf no blue light by Paul15578 on Sat, 2017-11-04 04:00 |
2 |
by Paul15578 Mon, 2017-11-06 13:56 |
VESC Original Hardware | |
|
mcpwm_set_current VS mcpwm_set_brake_current by stiganielsen on Wed, 2019-09-11 15:40 |
2 |
by mechhead Mon, 2022-02-14 11:04 |
VESC Firmware | |
|
VESC 4.12 +5v output by lennarn on Tue, 2020-04-28 15:35 |
2 |
by sandrino Mon, 2023-01-23 16:01 |
VESC Original Hardware | |
|
Constant RPM not accurate - Please help by TooSlow2Care on Sat, 2020-11-28 23:39 |
2 |
by Luke264 Wed, 2020-12-09 19:59 |
General discussion | |
|
Cut off after reaching Max. Duty Cycle by toboli on Thu, 2023-06-01 22:54 |
2 |
by toboli Sat, 2023-07-01 13:32 |
General discussion | |
|
Massive overshoot in BLDC current control by chris1seto on Tue, 2019-04-09 20:10 |
2 |
by frank Thu, 2019-04-11 11:40 |
Third Party Hardware | |
|
Brake lever Cutoff switch seperate from Regen braking/throttle wheel by SuperSpeed Scooter on Thu, 2022-11-03 19:13 |
2 |
by oangelo Wed, 2023-01-11 12:25 |
General discussion | |
|
RPM increase by Tibor Kalman Za... on Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
VESC Tool | |
|
Connect VESC to Keyboard/Wireless Joystick by sanketh1691 on Mon, 2021-10-04 20:58 |
2 |
by sanketh1691 Wed, 2021-10-06 18:58 |
VESC Tool | |
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen on Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
General discussion | |
|
Is there a workaround to set regen voltage, not current? by Gsorter on Sat, 2023-03-11 17:59 |
2 |
by Gsorter Sat, 2023-03-11 23:48 |
General discussion | |
|
Vesc 6 Hardware layout releasing "in the near future" by david_hickox on Wed, 2018-03-07 04:42 |
2 |
by TechAUmNu Wed, 2018-04-04 21:11 |
VESC6 Beta | |
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman on Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
Third Party Hardware | |
|
Change RPM of motor by Gas_Sn4ke on Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
General discussion |
Pages
