You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Use Mutexes within the ppm app by talabo on Thu, 2021-07-15 12:25 |
by talabo Thu, 2021-07-15 12:25 |
VESC Firmware | ||
|
Write motor configuration from XML file in 3rd app by jernejm on Tue, 2022-03-29 11:56 |
by jernejm Tue, 2022-03-29 11:56 |
VESC Firmware | ||
|
Impact of motor resistance value vs temperature by Torbjorn on Fri, 2022-12-16 09:09 |
by Torbjorn Fri, 2022-12-16 09:09 |
General discussion | ||
|
Front hub motor on an X11 citycoco fat tire electric trike. by oangelo on Thu, 2022-12-08 22:57 |
by oangelo Thu, 2022-12-08 22:57 |
General discussion | ||
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin on Sat, 2025-04-26 07:38 |
by Oriessin Sat, 2025-04-26 07:38 |
General discussion | ||
|
HFI and braking by aethyr on Thu, 2020-03-19 21:01 |
by aethyr Thu, 2020-03-19 21:01 |
General discussion | ||
|
Help with more torque with vesc by Juzy on Wed, 2025-04-02 04:52 |
by Juzy Wed, 2025-04-02 06:59 |
VESC Tool | ||
|
Phase voltage rise time by CTSchorsch on Wed, 2020-10-07 14:09 |
by CTSchorsch Wed, 2020-10-07 14:09 |
Third Party Hardware | ||
|
Looking for paid help to customize VESC board by jwardellMLA on Thu, 2022-06-09 20:34 |
by jwardellMLA Thu, 2022-06-09 20:34 |
Third Party Hardware | ||
|
Upgrading to higher voltage setup by JPK2 on Wed, 2024-06-05 22:11 |
by JPK2 Wed, 2024-06-05 22:11 |
General discussion | ||
|
best way to control motor over UART by harold on Fri, 2026-02-13 15:31 |
by harold Mon, 2026-02-16 16:06 |
Projects incorporating VESC technology | ||
|
A mini FOC driver(small,low cost) by ncer on Sun, 2021-05-16 07:01 |
by ncer Sun, 2021-05-16 07:03 |
Third Party Hardware | ||
|
wheelchair with a joystick via Vesc by hopeingod on Fri, 2024-05-17 12:00 |
by hopeingod Fri, 2024-05-17 12:00 |
General discussion | ||
|
VESC 6 MK5 Dectection Failed DRV fault by Than on Thu, 2025-12-18 03:02 |
by Than Thu, 2025-12-18 03:02 |
Third Party Hardware | ||
|
Limiting Down hill speed by dbau on Sat, 2022-01-29 06:54 |
by dbau Sat, 2022-01-29 09:19 |
General discussion | ||
|
How to start with vesc source code ? by cmarc on Tue, 2020-01-28 15:48 |
by cmarc Tue, 2020-01-28 15:48 |
General discussion | ||
|
Vesc Tool cannot detect firmware by MARK EVERITT on Sat, 2018-06-30 18:36 |
by MARK EVERITT Sat, 2018-06-30 18:36 |
VESC Firmware | ||
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning on Mon, 2024-12-02 13:19 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
VESC Tool | ||
|
Freewheeling by Stianaj on Fri, 2020-01-17 19:15 |
by Stianaj Fri, 2020-01-17 19:15 |
VESC Tool | ||
|
customer app for pwm input by ccrbs on Tue, 2020-08-11 12:06 |
by ccrbs Tue, 2020-08-11 12:06 |
General discussion |
Pages
