You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
CanOpen by maxmertins on Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
General discussion | |
|
Using reverse with a spare channel by spork on Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
General discussion | |
|
Delay on reverse function on electric boat by FreddyForLaunch on Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
VESC Tool | |
|
VESC 75/300 with sin/cos encoder by sajjen on Tue, 2019-11-12 16:16 |
4 |
by marcos_ Sun, 2020-01-19 22:48 |
VESC Original Hardware | |
|
VESC Tool 3.0 can't run input wizzard by thib on Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
VESC Tool | |
|
half speed on FOC vs BLDC by ever.summer on Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
General discussion | |
|
PAS sensor for pedelec and speed pedelec by th0masrtg on Sun, 2020-04-26 08:55 |
4 |
by th0masrtg Thu, 2020-10-29 07:38 |
Feature Requests | |
|
Too little torque. by Roger Wolff on Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
General discussion | |
|
Setting up low KV brushless motor? by Trent on Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
General discussion | |
|
Porting to a newer STM32 by TechAUmNu on Wed, 2020-09-16 12:38 |
4 |
by STEPHY AKKARA Thu, 2022-04-14 07:57 |
VESC Firmware | |
|
Anti cogging, suppressing torque ripple? by Alistair Goodman on Wed, 2022-01-19 11:33 |
4 |
by Alistair Goodman Thu, 2022-01-20 11:11 |
General discussion | |
|
VESC 6 CAN Command and Telemetry Formats by TerraHawk on Thu, 2019-11-21 20:29 |
4 |
by flatspot Tue, 2020-11-10 07:31 |
VESC Firmware | |
|
Docker images for vesc build? by dammfine on Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
VESC Tool | |
|
VESC 6 hi voltage problem by mike on Fri, 2018-05-04 11:34 |
4 |
by mike Tue, 2018-05-08 19:31 |
General discussion | |
|
VESC for RC Powerboat by martin2day on Wed, 2021-02-17 13:02 |
4 |
by martin2day Tue, 2021-07-13 11:50 |
Third Party Hardware | |
|
Dead VESC. Power up when motor is spinning. by Bor Zabric on Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
General discussion | |
|
Maximum Duty Cycle limit is 95% by shimdidly on Sun, 2017-10-01 19:59 |
4 |
by shimdidly Sat, 2017-10-07 01:42 |
VESC Tool | |
|
UART CAN forwarding by frankus on Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
General discussion | |
|
FSESC 4.20 Tuning for RC ESC? by Abcc123 on Thu, 2022-09-01 04:41 |
4 |
by Abcc123 Wed, 2022-09-07 00:23 |
General discussion | |
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog on Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
General discussion |
Pages
