You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
How do I compile the VESC Tool? by ipbyrne on Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
VESC Tool | |
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel on Fri, 2020-03-20 03:45 |
4 |
by TheFallen Mon, 2021-03-01 16:47 |
General discussion | |
|
Motor temperature increase by e-biker on Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
General discussion | |
|
Data logging by charper on Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
VESC Tool | |
|
VESC 100/250 by electricfox on Mon, 2020-01-13 20:23 |
4 |
by vitormhenrique Thu, 2020-02-13 01:12 |
VESC Original Hardware | |
|
Positional Control, Hall Sensor by wdaehn on Fri, 2017-12-08 15:02 |
4 |
by wdaehn Mon, 2017-12-25 09:46 |
General discussion | |
|
CanOpen by maxmertins on Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
General discussion | |
|
controlling 2 motors for two directions each by ori harush on Mon, 2022-06-06 07:17 |
4 |
by Indy8976 Tue, 2022-06-21 13:36 |
General discussion | |
|
Measure resistance with IGBTs by mtzm on Wed, 2018-04-04 14:46 |
4 |
by jaredreese Thu, 2019-10-03 11:41 |
VESC Firmware | |
|
how to download v5.03 firmware? by barncat08 on Wed, 2022-01-26 18:35 |
4 |
by Gatze Sat, 2022-04-23 11:48 |
VESC Firmware | |
|
Firmware update thru UART? by cromoly on Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
General discussion | |
|
Custom VESC4.8 short circuit error by b4zz on Mon, 2018-12-17 10:26 |
4 |
by b4zz Wed, 2018-12-19 16:48 |
Third Party Hardware | |
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons on Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
VESC Original Hardware | |
|
Is the Vesc 5 mkIII capable of 13s li-Ion (fully charged 54,6V) by Pelle on Sun, 2020-04-12 12:09 |
4 |
by danilolattaro Thu, 2021-04-22 14:50 |
General discussion | |
|
VESC amplifier ? by Markula on Fri, 2020-11-13 14:52 |
4 |
by s0313045 Mon, 2020-11-16 23:50 |
General discussion | |
|
How to interpret the result of "last_adc_duration" (terminal command)? by RSR on Fri, 2017-09-08 15:55 |
4 |
by RSR Sat, 2017-09-09 18:38 |
VESC Firmware | |
|
Wand speed display incorrect - Solved by hans_maier on Sat, 2019-09-14 15:16 |
4 |
by hans_maier Wed, 2019-09-18 22:31 |
General discussion | |
|
FSESC 4.20 Tuning for RC ESC? by Abcc123 on Thu, 2022-09-01 04:41 |
4 |
by Abcc123 Wed, 2022-09-07 00:23 |
General discussion | |
|
Motor spins only with outside help by asaf123098 on Thu, 2019-04-04 06:52 |
4 |
by dekafive Thu, 2019-06-20 11:36 |
Third Party Hardware | |
|
How to tell what HW version I have and set conf_general.h by jmachuca77 on Fri, 2021-02-19 19:21 |
4 |
by danilolattaro Mon, 2021-04-12 19:38 |
VESC Development and Beta Testing |
Pages
