You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
VESC regenerating while RPM increased by olivierskypullc... on Fri, 2019-03-08 16:32 |
2 |
by olivierskypullc... Mon, 2019-03-11 10:45 |
General discussion | |
|
Motor moves jerky by dsuresh on Thu, 2021-03-04 19:38 |
2 |
by dsuresh Fri, 2021-03-05 18:17 |
General discussion | |
|
Vesc motor resistance value by HiandHello on Wed, 2023-02-15 07:45 |
2 |
by HiandHello Wed, 2023-02-15 22:57 |
VESC Original Hardware | |
|
Hall sensor problems by Traceo on Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
VESC Tool | |
|
Question about custom coding to shutdown the motor by dsuresh on Fri, 2021-04-30 18:51 |
2 |
by dsuresh Sun, 2021-05-02 23:41 |
General discussion | |
|
ws8212 and VESC firmware by dannlh on Fri, 2017-11-03 04:17 |
2 |
by dannlh Sat, 2017-11-04 18:47 |
General discussion | |
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu on Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
VESC Tool | |
|
Timeout Brake Current [Fail Save] by Cuprani on Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
General discussion | |
|
Uploading compiled firmware results in no USB access by Count1310 on Sat, 2020-08-08 14:45 |
2 |
by ibarretos Sun, 2020-08-30 13:34 |
VESC Firmware | |
|
Motor stopped and I had to run Setup Motors FOC wizard to get it going again by JasonBear on Fri, 2025-11-14 13:24 |
2 |
by JasonBear Sun, 2025-11-16 20:41 |
General discussion | |
|
Current limit problem by albheim on Fri, 2022-09-09 10:34 |
2 |
by albheim Fri, 2022-09-09 13:24 |
General discussion | |
|
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle on Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
General discussion | |
|
Red Flashing Light? by givol on Sat, 2019-06-29 19:01 |
2 |
by frank Sun, 2019-07-21 18:25 |
Third Party Hardware | |
|
Are all VESC based ESCs within the same generation standardized in their sensors and data payloads? by pearlgreymusic on Sat, 2022-08-27 11:43 |
2 |
by pearlgreymusic Tue, 2022-09-06 14:24 |
General discussion | |
|
NEW HARDWARE RELEASED!!! | DF_ESC Electric Motor Controller | YouTube Series Walkthrough by d.fresu on Tue, 2023-08-01 09:29 |
2 |
by NOAI Mon, 2023-09-04 08:14 |
Projects incorporating VESC technology | |
|
IMU and ADC1/2 not working by Dwal on Wed, 2021-05-26 18:05 |
2 |
by Dwal Thu, 2021-06-03 22:34 |
General discussion | |
|
Motor setup help please by TrevM on Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
VESC Tool | |
|
WAND -Joystick faulty- by chris_winkel on Wed, 2022-03-23 17:53 |
2 |
by chris_winkel Mon, 2022-03-28 11:14 |
VESC Original Hardware | |
|
4.2 hw Erpm bldc mode by Katt on Wed, 2021-01-27 15:48 |
2 |
by Katt Tue, 2021-02-02 14:16 |
General discussion | |
|
Erratic braking on vesc using large hub motor. by jtechbop on Sun, 2021-09-19 06:54 |
2 |
by jtechbop Tue, 2021-10-19 20:59 |
General discussion |
Pages
