You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
ADC MAX Voltage 5volt ? by liteglow on Sat, 2020-07-25 23:48 |
by liteglow Sat, 2020-07-25 23:48 |
VESC Tool | ||
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
How to set a jog speed using an encoder by AK6302019 on Wed, 2019-08-07 15:42 |
by AK6302019 Wed, 2019-08-07 15:42 |
General discussion | ||
VESC ramping problem by andrii619 on Mon, 2020-03-23 21:45 |
by andrii619 Mon, 2020-03-23 21:45 |
VESC Firmware | ||
VESC 4.12 wont connect to pc by stefann on Sun, 2020-03-15 00:42 |
by stefann Sun, 2020-03-15 00:42 |
VESC Original Hardware | ||
Minimum speed push cart using arduino by BarBumble on Wed, 2021-05-12 09:29 |
by BarBumble Wed, 2021-05-12 09:29 |
General discussion | ||
Current sensor and commanded current by galp on Fri, 2019-02-22 23:08 |
by galp Fri, 2019-02-22 23:08 |
General discussion | ||
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly on Sun, 2017-10-15 00:48 |
by shimdidly Sun, 2017-10-15 00:48 |
VESC Tool | ||
Why android app doesn't save the BALANCE settings in the motors profile? Is it a BUG? by zmei116 on Fri, 2020-05-29 23:31 |
by zmei116 Fri, 2020-05-29 23:31 |
VESC Original Hardware | ||
Reusing pin in custom application by Pechvogel on Wed, 2021-01-13 07:12 |
by Pechvogel Wed, 2021-01-13 07:12 |
VESC Firmware | ||
VESC Tool app min hardware requirements by flix on Sat, 2022-04-16 22:13 |
by flix Sat, 2022-04-16 22:13 |
VESC Tool | ||
Lehner TorQstar any experience by fabu80 on Wed, 2023-02-01 08:35 |
by fabu80 Wed, 2023-02-01 08:35 |
General discussion | ||
Slowing down the speed when in low battery state by dsuresh on Tue, 2021-03-16 21:59 |
by dsuresh Tue, 2021-03-16 21:59 |
General discussion | ||
Throttle and Brake by shatty on Wed, 2021-03-10 01:19 |
by shatty Wed, 2021-03-10 01:22 |
VESC Tool | ||
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:45 |
by alexshen2012 Fri, 2022-07-01 05:45 |
General discussion | ||
VESC 75100 motor detection fine but then motor won't run just shudders and resistance by Jidobaba on Sun, 2024-04-21 03:17 |
by Jidobaba Sun, 2024-04-21 03:17 |
General discussion | ||
Problem report: VESC keeps running at full reverse throttle after PPM input returns to mid-stick by chunkulator on Sun, 2019-08-11 00:34 |
by chunkulator Sun, 2019-08-11 00:34 |
VESC Firmware | ||
Where to find codelines for speed and position control structure by kianK on Tue, 2022-03-01 15:25 |
by kianK Thu, 2022-03-03 12:23 |
VESC Firmware | ||
how do you arm your Vesc in arduino code? by the creator on Wed, 2019-03-13 01:11 |
by the creator Wed, 2019-03-13 01:33 |
General discussion | ||
VESC Tool Makes my remote unusable by IcecreamSamurai on Mon, 2020-06-15 01:49 |
by IcecreamSamurai Mon, 2020-06-15 01:49 |
VESC Tool |