You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
duty cicle 95% but current not at max by rodrigo.baronio on Mon, 2023-02-06 15:52 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
VESC Tool | ||
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc on Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
VESC Tool | |
|
Motor not running after applying SINE/COSINE settings by DHOUT on Fri, 2023-01-27 03:32 |
by DHOUT Fri, 2023-01-27 03:32 |
VESC Tool | ||
|
Motors spin up during detection but then won't move by jordan314 on Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
VESC Tool | |
|
Firmware issues by salvasalce on Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
VESC Tool | |
|
I made a Boost Current Mod by JL2579 on Tue, 2018-01-23 18:28 |
10 |
by phiger Wed, 2022-12-21 11:19 |
VESC Tool | |
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 on Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
VESC Tool | |
|
Voltage measurement calibration? by pyryjansson on Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
VESC Tool | |
|
Serial Control From PC by aguzel on Fri, 2020-08-21 02:45 |
3 |
by Jens Mon, 2022-11-28 20:40 |
VESC Tool | |
|
Cannot connect to vesc tool app by sharpshooterjd on Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
VESC Tool | |
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto on Sun, 2022-11-27 16:34 |
by Miniproto Sun, 2022-11-27 16:34 |
VESC Tool | ||
|
Motor always accelerates to maximum speed by zapshe on Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
VESC Tool | |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp on Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
VESC Tool | |
|
Problem to configure my esc with PWM-signal by Lucar on Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
VESC Tool | |
|
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
VESC Tool | |
|
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota on Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
VESC Tool | |
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
Unable to connect to vesc through can bus by Kupofty on Thu, 2022-10-20 16:24 |
by Kupofty Thu, 2022-10-20 16:24 |
VESC Tool | ||
|
TWO MOTOR SYSTEM by ronmotor on Mon, 2022-10-17 00:44 |
by ronmotor Mon, 2022-10-17 00:44 |
VESC Tool |
Pages
