You are here
Third Party Hardware
Log in to post new content in the forum.
Topic / Topic starter | Replies |
Last post![]() |
|
---|---|---|---|
Change maximum allowed input voltage by CTSchorsch » Mon, 2021-12-13 21:37 |
2 |
by CTSchorsch Tue, 2021-12-14 21:47 |
|
Current Sensor by CTSchorsch » Fri, 2021-12-03 14:53 |
3 |
by R4850S1 Sat, 2021-12-04 08:57 |
|
Connect PixHawk 4 to FSESC 4.12 by iwdok » Tue, 2021-10-19 11:18 |
2 |
by frank Wed, 2021-12-01 13:38 |
|
Flipsky FSESC 4.12 Bluetooth over mini USB? by blaz.ferlic » Fri, 2021-11-19 10:18 |
3 |
by lurch Fri, 2021-11-19 14:00 |
|
Single Flipsky FSESC 6.6 getting started and IMU data by alexantosh » Wed, 2021-04-07 12:32 |
0 |
by alexantosh Mon, 2021-11-15 13:10 |
|
INA240A1 replacement by CTSchorsch » Thu, 2021-11-11 15:50 |
3 |
by skyline1970 Sat, 2021-11-13 11:37 |
|
FSESC 4.2 problem at full speed .. by lurch » Fri, 2021-10-22 19:27 |
4 |
by lurch Mon, 2021-11-01 15:09 |
|
Turnigy Sk8 ESC - pulls voltage to zero by mnetterberg » Wed, 2021-09-29 10:17 |
1 |
by skyline1970 Mon, 2021-11-01 07:55 |
|
Which hall sensor should i buy? by qwerasdf » Sun, 2021-09-19 19:50 |
1 |
by skyline1970 Sat, 2021-10-30 16:00 |
|
Flipsky Mini FSESC4.2 Questions by Laurie Forbes » Sat, 2021-10-02 18:54 |
1 |
by skyline1970 Fri, 2021-10-29 12:09 |
|
Need to integrate 4 motor controllers for sensored motors by charlesrwest » Sun, 2021-09-26 20:19 |
1 |
by skyline1970 Fri, 2021-10-29 12:01 |
|
Best hardware platform for firmware development by kubark42 » Thu, 2021-10-14 19:59 |
3 |
by district9prawn Wed, 2021-10-20 00:01 |
|
Motor is too loud, are there settings to quiet it? by Jason Toews » Thu, 2021-09-23 20:49 |
2 |
by Laurie Forbes Thu, 2021-09-30 18:57 |
|
4.12 Hardware without drv chip by Gatze » Thu, 2021-08-26 11:13 |
1 |
by skyline1970 Sat, 2021-09-18 11:32 |
|
Flipsky Dual FSESC6.6 loses connection, connected BLDC buzzing after restart by gabrielredding » Mon, 2019-04-29 00:00 |
3 |
by Constantin00 Fri, 2021-09-17 11:00 |
|
Issues flashing VESC HW 4.12 by Nic_cfar » Wed, 2020-10-21 00:08 |
1 |
by xeniter Mon, 2021-09-13 22:33 |
|
How to start a new VESC 6 hardware project by olek130 » Sun, 2021-08-15 18:10 |
1 |
by vadicus Sun, 2021-08-22 04:31 |
|
Vesc tool app x Spinted Ubox by Thomas Leduc » Fri, 2021-07-16 10:10 |
0 |
by Thomas Leduc Mon, 2021-08-16 08:50 |
|
Cheap remote from cheap board by Remind » Sun, 2021-08-15 02:06 |
0 |
by Remind Sun, 2021-08-15 02:06 |
|
Esc does not reply by nemethLali » Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
|
Need Your Help with PPM Mapping Remote during Setup by silverglate » Sun, 2019-02-03 05:04 |
31 |
by xapek2008 Fri, 2021-07-16 16:07 |
|
VESC for RC Powerboat by martin2day » Wed, 2021-02-17 13:02 |
4 |
by martin2day Tue, 2021-07-13 11:50 |
|
TINY6 by Sojourn » Mon, 2021-05-31 03:20 |
1 |
by TVAVAE Sat, 2021-07-10 00:46 |
|
Which STM32F4 MCU's can be used? by nxtv2 » Sun, 2021-03-21 11:54 |
6 |
by TVAVAE Sat, 2021-07-10 00:40 |
|
Porting VESC firmware to ODrive hardware by Remind » Wed, 2021-06-30 01:39 |
3 |
by vadicus Thu, 2021-07-08 07:34 |
Log in to post new content in the forum.
