You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
How to increase startup torque? by Enak » Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
|
|
How to get vesc tool for linux on ubuntu? by vitormhenrique » Tue, 2019-10-22 16:00 |
7 |
by JackGunnarsson Mon, 2023-10-02 13:20 |
|
|
How to get Max Torque at start by player107 » Fri, 2023-04-07 09:55 |
4 |
by Trooth Fri, 2024-02-23 06:52 |
|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
|
How to determine motor size in wizard, hub motors ? by Photolad61 » Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
|
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
|
how to communication with arduino on vesc via CAN by yuri12 » Tue, 2022-02-08 13:16 |
0 |
by yuri12 Tue, 2022-02-08 13:16 |
|
|
How to adjust ADC1 parameters to adjust the speed (not working) by player107 » Fri, 2023-04-14 13:46 |
0 |
by player107 Fri, 2023-04-14 13:46 |
|
|
How to access VESC error codes in the new VESC tool by berno3 » Tue, 2018-06-05 08:47 |
1 |
by Roger Wolff Wed, 2018-06-06 07:36 |
|
|
How do I disable brake? by moo10032 » Tue, 2021-02-23 08:09 |
0 |
by moo10032 Tue, 2021-02-23 08:10 |
|
|
How do I compile the VESC Tool? by ipbyrne » Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
|
|
How can we log all the real time data like motor current, battery current,etc to analyze them later? by vimi94 » Thu, 2019-05-02 09:57 |
25 |
by Toto Tue, 2023-03-07 14:40 |
|
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne » Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
|
|
Hoverboard Motor Setup by CadillacF1 » Sat, 2020-07-11 05:26 |
2 |
by TheFallen Mon, 2020-08-17 12:14 |
|
|
Hoverboard motor Reverse direction by Silvio Semedo » Sat, 2021-01-16 17:43 |
1 |
by skyline1970 Sun, 2021-02-07 17:32 |
|
|
High Current Sampling Mode True 80% current by antonchromjak » Sun, 2017-09-24 21:14 |
2 |
by antonchromjak Wed, 2017-09-27 19:59 |
|
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:02 |
0 |
by stefann Wed, 2020-04-08 23:02 |
|
|
help with vesc real time data trouble shooting by stefann » Wed, 2020-04-08 23:03 |
0 |
by stefann Wed, 2020-04-08 23:03 |
|
|
Help with a settings for only generator by Mafo » Fri, 2018-03-02 16:59 |
6 |
by Mafo Thu, 2018-03-15 11:15 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
|
|
Help needed for VESC set up! by mbagrey » Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
|
|
Help i can not setup my motors by jakson01 » Fri, 2022-09-09 18:37 |
0 |
by jakson01 Fri, 2022-09-09 18:37 |
|
|
Hall sensor problems by Traceo » Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
|
|
Hall sensor data is all 0. What do? by Byproduct » Sat, 2023-01-14 14:39 |
0 |
by Byproduct Wed, 2023-02-08 11:21 |
Log in to post new content in the forum.
