You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Configuration of underwater thruster by UnderwaterMotors » Fri, 2023-03-24 18:10 |
0 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
|
|
Vesc 75100 by Matteo Christian » Wed, 2023-05-31 13:32 |
0 |
by Matteo Christian Fri, 2023-06-09 12:08 |
|
|
VESC App - Android - "App not installed" error by KColborne » Mon, 2023-03-27 22:11 |
0 |
by KColborne Mon, 2023-03-27 22:11 |
|
|
Dual VESC via CAN by scholtylicious » Sat, 2021-03-13 15:56 |
0 |
by scholtylicious Sat, 2021-03-13 15:56 |
|
|
VESC back-current safety? by randohinn » Mon, 2019-04-15 16:37 |
0 |
by randohinn Mon, 2019-04-15 16:37 |
|
|
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce » Mon, 2021-03-15 03:31 |
0 |
by Bruce Mon, 2021-03-15 03:31 |
|
|
HM-10 BLE adapter? by ziumus » Mon, 2019-04-22 00:42 |
0 |
by ziumus Mon, 2019-04-22 00:42 |
|
|
Observer tracking fail by dangminhducnbk » Sun, 2019-02-17 14:09 |
0 |
by dangminhducnbk Sun, 2019-02-17 14:09 |
|
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
|
Changing the timer for VESC auto turn off timing by dsuresh » Mon, 2021-03-15 21:19 |
0 |
by dsuresh Mon, 2021-03-15 21:19 |
|
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
|
Flipsky6.6 usb not detected This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
|
4.12 cooling mod by thewho » Wed, 2019-05-01 18:45 |
0 |
by thewho Wed, 2019-05-01 18:45 |
|
|
Can someone verify this by jsbenson » Mon, 2023-06-26 09:22 |
0 |
by jsbenson Tue, 2023-06-27 07:50 |
|
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
|
VESC 6: frequent direction change application problem by cromoly » Thu, 2019-05-02 01:45 |
0 |
by cromoly Thu, 2019-05-02 01:45 |
|
|
Motors spin during detection but then won't spin by jsbenson » Tue, 2023-06-27 23:54 |
0 |
by jsbenson Tue, 2023-06-27 23:54 |
|
|
Minimum speed push cart using arduino by BarBumble » Wed, 2021-05-12 09:29 |
0 |
by BarBumble Wed, 2021-05-12 09:29 |
|
|
VESC6 cooked MOSFET by hagoston » Mon, 2021-03-22 14:23 |
0 |
by hagoston Mon, 2021-03-22 15:03 |
|
|
RPM Control Problems by MrMonk3y » Mon, 2019-05-06 22:54 |
0 |
by MrMonk3y Mon, 2019-05-06 22:54 |
|
|
12v(3s) Input to VESC 75/250 by AliBarrett10 » Wed, 2021-03-24 14:36 |
0 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
|
Log in to post new content in the forum.
