You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Designing a robust power stage using Mosfets by ripperpc » Tue, 2020-05-05 08:04 |
0 |
by ripperpc Tue, 2020-05-05 08:04 |
|
|
How different of VESC 6 and VESC 4 by Ken_chen » Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
|
|
How the saliency is affecting the High frequency signal injection? by SOURAV UK » Sun, 2020-05-03 11:35 |
0 |
by SOURAV UK Sun, 2020-05-03 11:35 |
|
|
How I control the RPM of my motor from VESC with Arduino? by George W. » Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
|
|
program motorstop for VTOL by Jan-Willem » Wed, 2020-04-29 18:55 |
4 |
by frank Thu, 2020-04-30 18:08 |
|
|
VESC/FOC developer needed by CAYAGO_MS » Thu, 2020-04-30 14:23 |
0 |
by CAYAGO_MS Thu, 2020-04-30 14:23 |
|
|
Hoyt Puck Prototipo DSS50+ Firmware questions by tombell » Wed, 2020-04-29 03:56 |
0 |
by tombell Wed, 2020-04-29 03:56 |
|
|
22 pole motor and potentiometer throttle by Kenneth » Mon, 2020-04-27 23:01 |
1 |
by Kenneth Tue, 2020-04-28 08:59 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:30 |
0 |
by AllenFF Mon, 2020-04-27 15:34 |
|
|
VESC for EU pedelecs by bb67 » Mon, 2020-04-27 14:11 |
0 |
by bb67 Mon, 2020-04-27 14:13 |
|
|
Battery charging using motor inductance by eptv » Sun, 2020-04-26 07:44 |
0 |
by eptv Sun, 2020-04-26 07:44 |
|
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 » Tue, 2020-04-21 17:40 |
3 |
by cjjohnson97 Fri, 2020-04-24 21:38 |
|
|
Firmware Update = Quiet Motor? by worldmaverik » Sun, 2020-04-19 21:45 |
0 |
by worldmaverik Sun, 2020-04-19 21:45 |
|
|
Custom VESC4 hardware - disable Regen? by ben5243 » Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
|
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung » Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
|
|
How to update firmware over CAN bus by andrii619 » Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
|
|
No, BLDC is not dead. by Pimousse » Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
|
|
4 vesc motors at once? by i-make-robots » Thu, 2020-04-16 02:17 |
1 |
by hexakopter Sat, 2020-04-18 12:20 |
|
|
Newbie Help please, Longer run time? by Bildoon » Mon, 2020-04-06 02:00 |
1 |
by linsus Thu, 2020-04-16 14:18 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:27 |
0 |
by AllenFF Wed, 2020-04-15 03:27 |
|
|
Welding with the VESC by doomy1986 » Mon, 2020-04-13 14:38 |
0 |
by doomy1986 Mon, 2020-04-13 14:38 |
|
|
Using STM32F407 for a custom board by kapek » Mon, 2020-04-06 04:16 |
2 |
by vadicus Fri, 2020-04-10 06:31 |
|
|
Delayed start for slave motor by rsknudsen-dk » Mon, 2020-04-06 10:06 |
0 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
|
|
VESC Calculator by lmochsner » Thu, 2020-04-02 05:13 |
0 |
by lmochsner Thu, 2020-04-02 05:13 |
Log in to post new content in the forum.
