You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Trying to make motor-control work for predetermined motions, could use some help by Davideo » Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
|
|
Simulating controller accurately by TechAUmNu » Fri, 2019-08-16 15:35 |
0 |
by TechAUmNu Fri, 2019-08-16 15:35 |
|
|
understanding switching frequency and dutycycle by speed3r » Thu, 2019-08-08 13:36 |
3 |
by speed3r Thu, 2019-08-15 09:26 |
|
|
Need help to configure the regenerative brake ... by Loops » Mon, 2019-08-12 19:43 |
2 |
by Loops Wed, 2019-08-14 18:07 |
|
|
Reverse ADC and UART by ben_src » Mon, 2019-08-12 17:22 |
0 |
by ben_src Mon, 2019-08-12 17:22 |
|
|
UART communication by EthB » Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
|
|
How to set a jog speed using an encoder by AK6302019 » Wed, 2019-08-07 15:42 |
0 |
by AK6302019 Wed, 2019-08-07 15:42 |
|
|
"Throttle" help by benha » Wed, 2019-08-07 05:58 |
0 |
by benha Wed, 2019-08-07 05:58 |
|
|
VESC PID not working by vulkan66 » Tue, 2019-07-30 10:29 |
2 |
by vulkan66 Sun, 2019-08-04 17:13 |
|
|
Controlling VESC with arduino - by vulkan66 » Thu, 2019-07-11 11:51 |
3 |
by vulkan66 Thu, 2019-08-01 21:34 |
|
|
Is the Diy pcb version still working? by jon218white » Sat, 2019-07-27 00:58 |
1 |
by skyline1970 Wed, 2019-07-31 13:33 |
|
|
VESC CAN_STATUS_1_2_3_4 explained (RPi) by kimpet » Mon, 2019-05-13 12:51 |
3 |
by Jack_Li Tue, 2019-07-30 14:01 |
|
|
FSESC6.6 and Rpi via UART - Understanding the software by gabrielredding » Sat, 2019-07-06 02:50 |
3 |
by abrac Mon, 2019-07-29 14:11 |
|
|
VESC with no working brake button by tavsanist » Sat, 2019-07-27 02:40 |
0 |
by tavsanist Sat, 2019-07-27 02:40 |
|
|
Weird BLDC Current Waveform by thepcman » Thu, 2019-07-25 10:38 |
0 |
by thepcman Thu, 2019-07-25 10:41 |
|
|
No Option for Master or Slave on SetUp Input? by trickleung91 » Sun, 2019-06-30 09:06 |
1 |
by frank Sun, 2019-07-21 18:46 |
|
|
lower power output than expected by mxpro32 » Tue, 2019-06-18 21:38 |
3 |
by frank Sun, 2019-07-21 18:39 |
|
|
Current loop resonance in higher ERPM under Current Mode by ypl » Sat, 2019-07-20 09:34 |
0 |
by ypl Sat, 2019-07-20 09:34 |
|
|
Efficiency Control by devin » Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
|
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li » Fri, 2019-07-05 06:55 |
0 |
by Jack_Li Fri, 2019-07-05 06:58 |
|
|
Something about encoder connection by ztwsa007 » Mon, 2019-07-01 13:43 |
1 |
by ztwsa007 Fri, 2019-07-05 03:26 |
|
|
step by step ebike thorttle setup by sindre » Wed, 2019-07-03 17:59 |
0 |
by sindre Wed, 2019-07-03 17:59 |
|
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
|
5V/serial weirdness when using FOC by wihrl » Sat, 2019-06-15 12:57 |
1 |
by frank Fri, 2019-06-28 14:13 |
|
|
Low duty cycle issues by nathantarlinton » Tue, 2019-06-25 03:01 |
1 |
by bobfrank Tue, 2019-06-25 03:39 |
Log in to post new content in the forum.
