You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
How to update a VESC 4.10 with a 3.36 firmware? by shingo.it on Tue, 2020-06-09 23:40 |
by shingo.it Tue, 2020-06-09 23:40 |
VESC Firmware | ||
How to update firmware over CAN bus by andrii619 on Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
General discussion | |
How to update VESC Tool? by Heimfried on Wed, 2020-02-05 10:35 |
2 |
by marialoise Fri, 2020-03-13 20:20 |
VESC Tool | |
How to upload firmware on MINI4 ? by john on Mon, 2018-11-12 10:55 |
1 |
by john Mon, 2018-11-12 11:59 |
Third Party Hardware | |
How to use an IMU and a PPM remote parallel by Gos1 on Tue, 2022-10-25 15:28 |
by Gos1 Wed, 2022-10-26 10:57 |
General discussion | ||
How to wire Cruise Control with VESC6 ADC by Tilman Baumann on Tue, 2018-04-10 11:11 |
by Tilman Baumann Tue, 2018-04-10 11:11 |
VESC Original Hardware | ||
How to wire MPU-9250 9DoF using SPI to vesc 6 mk4 by zmei116 on Fri, 2020-08-28 12:17 |
6 |
by TheFallen Mon, 2020-12-28 06:22 |
VESC Original Hardware | |
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li on Fri, 2019-07-05 06:55 |
by Jack_Li Fri, 2019-07-05 06:58 |
General discussion | ||
How trottle input by wire? by Heimfried on Mon, 2020-01-27 17:49 |
2 |
by Heimfried Mon, 2020-01-27 21:43 |
General discussion | |
How Update firmware vesc 6.41 with broken micro USB fw 3.40? by adrian210188 on Thu, 2020-03-12 01:18 |
1 |
by Pimousse Sat, 2020-03-21 13:01 |
VESC Firmware | |
how update from 2.18 to the latest firmware by aysubscriber@ic... on Tue, 2017-10-03 07:39 |
16 |
by JohnDip67 Fri, 2021-04-09 20:34 |
VESC Firmware | |
Hoyt Puck Prototipo DSS50+ Firmware questions by tombell on Wed, 2020-04-29 03:56 |
by tombell Wed, 2020-04-29 03:56 |
General discussion | ||
Hub motor e-bike not recognized by olivierskypullc... on Tue, 2019-04-16 11:06 |
3 |
by Ampit Fri, 2023-09-29 12:38 |
VESC Original Hardware | |
Hub motor FOC detection. by Roger Wolff on Tue, 2018-08-21 19:12 |
by Roger Wolff Tue, 2018-08-21 19:12 |
General discussion | ||
Hub Motor Gives up while Coasting With No Faults by vadicus on Sun, 2020-08-09 01:36 |
4 |
by vadicus Tue, 2020-08-11 18:01 |
General discussion | |
Hub Motor Remote Control by bf01 on Tue, 2017-11-14 16:04 |
3 |
by frank Wed, 2017-12-06 23:41 |
General discussion | |
Hub motor stutters at low RPM by winpark on Wed, 2020-09-02 00:53 |
3 |
by vadicus Tue, 2020-09-15 18:14 |
General discussion | |
HW 4.12 Change low voltage cutoff by subodh.malgonde on Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
VESC Original Hardware | |
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY on Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
VESC Original Hardware | |
HW advice : repair , vesc 4.12, vesc 6.4 or better wait ? by frameto on Sun, 2017-11-19 21:36 |
1 |
by josh Thu, 2018-07-26 18:47 |
Third Party Hardware |