You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Iron less Axialflux Motor by tobiokanobi on Sat, 2019-03-30 12:11 |
6 |
by kaanozgen Wed, 2020-02-26 11:42 |
VESC Original Hardware | |
Reconstruct detection control algorithm inside the tool by kaanozgen on Wed, 2020-02-26 18:50 |
by kaanozgen Wed, 2020-02-26 18:50 |
VESC Tool | ||
Motor detection accuracy in 3rd party hardware (old FW vs new FW) by shaman on Tue, 2020-02-25 16:03 |
3 |
by vadicus Wed, 2020-02-26 19:09 |
Third Party Hardware | |
Incorrect R and L detection? by vadicus on Mon, 2019-11-04 20:49 |
11 |
by vadicus Fri, 2020-02-28 00:21 |
Third Party Hardware | |
Duty cycle take 95% when motor released by Rarikao on Mon, 2019-12-23 08:57 |
2 |
by agnesnorris Sat, 2020-02-29 03:48 |
VESC Firmware | |
Motor draws current (up to 120 A), but doesn't turn by Heimfried on Sun, 2020-03-01 22:21 |
by Heimfried Sun, 2020-03-01 22:21 |
General discussion | ||
motorized kids pedal tractor app configuration by Tom1984 on Thu, 2020-02-27 16:58 |
2 |
by Philipp Spindler Mon, 2020-03-02 15:46 |
General discussion | |
Big Inrunner - Noisy In FOC Mode by skeaux on Mon, 2020-03-02 04:13 |
2 |
by skeaux Tue, 2020-03-03 05:30 |
General discussion | |
Vesc 75/300 max current by a727dd on Wed, 2020-03-04 04:34 |
by a727dd Wed, 2020-03-04 04:34 |
General discussion | ||
Holding torque in "Duty Cycle" mode by Petja on Mon, 2020-01-13 01:19 |
5 |
by pf26 Wed, 2020-03-04 08:58 |
General discussion | |
New version. by ThierryGTLTS on Thu, 2017-09-07 19:22 |
6 |
by Hectortcher Wed, 2020-03-04 11:21 |
VESC Tool | |
Enabling WS2811 not working by vitormhenrique on Thu, 2020-03-05 03:42 |
by vitormhenrique Thu, 2020-03-05 03:42 |
VESC Firmware | ||
What is limiting my RPMS (VESC 4.2 / Q100H setup) by nckbutler on Tue, 2020-03-03 15:37 |
1 |
by socrace Thu, 2020-03-05 03:50 |
General discussion | |
Vesc 75/300 burned by electricfox on Sat, 2020-02-15 22:35 |
8 |
by pf26 Fri, 2020-03-06 09:49 |
VESC Original Hardware | |
Can't update the VESC firmware by mansolander on Thu, 2020-03-05 11:30 |
1 |
by mansolander Fri, 2020-03-06 11:24 |
VESC Tool | |
5phase Vesc based on 75/300 by BartE on Thu, 2020-03-05 23:17 |
8 |
by vadicus Sun, 2020-03-08 05:51 |
General discussion | |
re-scaling CAN setDUTY CYCLE to -1 to 1 instead of 0 to 1 by a.dahhak on Fri, 2020-03-06 11:09 |
1 |
by a.dahhak Mon, 2020-03-09 10:38 |
VESC Firmware | |
Speed control by dent on Tue, 2020-03-10 20:11 |
2 |
by dent Wed, 2020-03-11 02:49 |
VESC Tool | |
VESC stopped working, can't connect to USB by Hyperion on Mon, 2018-04-09 16:53 |
6 |
by bloggerjaan Wed, 2020-03-11 12:31 |
General discussion | |
VESC - FAULT_CODE_DRV : motor no more spinning by piepolitb on Sat, 2018-05-19 12:27 |
4 |
by seif Wed, 2020-03-11 20:12 |
General discussion |