You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Notified of new version of firmware, can't DL it... by kchxaz on Sun, 2019-05-19 03:28 |
1 |
by hexakopter Sun, 2019-05-19 13:26 |
VESC Firmware | |
|
Reading tachometer over can bus by kimpet on Sun, 2019-05-12 22:24 |
5 |
by benjamin Sun, 2019-05-19 14:58 |
General discussion | |
|
Servomotor control with VESC6 by Humberto Estrada on Wed, 2019-05-22 16:15 |
by Humberto Estrada Wed, 2019-05-22 16:15 |
VESC Original Hardware | ||
|
Strange behaviour when controlling RPM by MrMonk3y on Wed, 2019-05-08 14:29 |
1 |
by cnd Mon, 2019-05-27 08:41 |
General discussion | |
|
half speed on FOC vs BLDC by ever.summer on Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
General discussion | |
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl on Tue, 2019-05-28 14:48 |
by Jackl Tue, 2019-05-28 14:48 |
VESC Original Hardware | ||
|
ADC Positive and Negative Ramping Time - not working by Astropower on Tue, 2019-05-28 22:41 |
by Astropower Tue, 2019-05-28 22:41 |
VESC Tool | ||
|
Arduino UART communication HW4.10 FW3.56 by joseguerra on Wed, 2019-05-22 13:01 |
1 |
by Pimousse Thu, 2019-05-30 17:23 |
General discussion | |
|
UART write read arduino by matiller on Sat, 2019-06-01 20:18 |
by matiller Sat, 2019-06-01 20:18 |
VESC Tool | ||
|
ERPM Limit Update Over CAN by josh on Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
Feature Requests | |
|
Dual control loop with magnetic encoders by wall0069 on Sun, 2019-06-02 05:39 |
by wall0069 Sun, 2019-06-02 05:39 |
Feature Requests | ||
|
What is a common motor efficiency? I'm at 72% by ever.summer on Tue, 2019-05-28 05:02 |
5 |
by Roger Wolff Sun, 2019-06-02 10:19 |
General discussion | |
|
VESC at very low speeds by LudoJ on Wed, 2019-05-15 16:09 |
1 |
by Roger Wolff Sun, 2019-06-02 10:25 |
General discussion | |
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 on Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
VESC Original Hardware | |
|
Brake Current Command Adjustments by josh on Fri, 2019-05-17 21:37 |
2 |
by josh Wed, 2019-06-05 17:14 |
General discussion | |
|
Step/Dir signals by wall0069 on Sun, 2019-06-09 16:06 |
by wall0069 Sun, 2019-06-09 16:06 |
General discussion | ||
|
Sync loss when switching from HALL to sensorless by blezalex on Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
General discussion | |
|
VESC not responding to Controller by jcab on Thu, 2018-03-08 21:51 |
4 |
by Popeye Mon, 2019-06-10 23:59 |
VESC Firmware | |
|
VESC 6 FOC wizard and current limitations. by Bor Zabric on Mon, 2019-06-10 21:12 |
1 |
by TechAUmNu Wed, 2019-06-12 14:42 |
General discussion | |
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion |
Pages
