You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
supported firmware by velolac on Mon, 2020-01-13 22:55 |
3 |
by velolac Tue, 2020-01-14 21:47 |
VESC Tool | |
|
arrow key hot working (neither on the app) but the board works correclty by lorenzidomenico94 on Tue, 2020-01-14 11:30 |
by lorenzidomenico94 Tue, 2020-01-14 11:30 |
VESC Tool | ||
|
Custom application and UART by Dennis Freiburg on Sat, 2020-01-11 13:19 |
3 |
by Dennis Freiburg Sun, 2020-01-12 19:37 |
General discussion | |
|
Filtering of motor temperature readings by Pedrodemio on Mon, 2019-07-01 22:16 |
8 |
by fessyfoo Sat, 2020-01-11 08:06 |
Feature Requests | |
|
Few questions by ElectroMagneto on Thu, 2020-01-09 23:57 |
10 |
by ElectroMagneto Sat, 2020-01-11 00:45 |
General discussion | |
|
VESC design specification, manual by velolac on Thu, 2020-01-02 15:54 |
1 |
by velolac Sat, 2020-01-11 00:05 |
VESC Original Hardware | |
|
No inbuilt NRF in vesc6 mkIII from Trampa: feel cheated, paid 300 pounds including customs by PREETHAMKS on Thu, 2020-01-09 15:36 |
1 |
by PREETHAMKS Thu, 2020-01-09 16:10 |
General discussion | |
|
Up dating firmware by rossco1959 on Mon, 2020-01-06 03:44 |
3 |
by rossco1959 Wed, 2020-01-08 02:06 |
General discussion | |
|
UART Accel/Gyro/Mag data by NATUITION on Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
General discussion | |
|
How to set up RF receiver for PPM or UART input? by adamdorr on Tue, 2020-01-07 16:23 |
by adamdorr Tue, 2020-01-07 16:23 |
General discussion | ||
|
Accessing the status LEDs by hrucker009 on Sun, 2020-01-05 20:09 |
1 |
by frank Tue, 2020-01-07 09:08 |
General discussion | |
|
Help calibrating a hub motor by Tin_Man_0 on Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
General discussion | |
|
Adding HM-10 Compatibility with Small Changes to Code by Jfriesen on Sat, 2018-06-09 00:45 |
5 |
by CTSchorsch Mon, 2020-01-06 07:11 |
VESC Tool | |
|
low voltage/power VESC by qdxiatao on Sun, 2019-12-29 09:27 |
2 |
by qdxiatao Mon, 2020-01-06 02:04 |
Third Party Hardware | |
|
Balance App by EVolution EV on Tue, 2019-12-31 05:11 |
by EVolution EV Thu, 2020-01-02 05:55 |
VESC Tool | ||
|
Protecting PSU with resistive load when braking by henxan on Sat, 2019-11-16 21:08 |
8 |
by Stupidspencer Mon, 2019-12-30 18:02 |
General discussion | |
|
motor detection - what to expect when spinning up the motor by grantmoy74 on Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
VESC Tool | |
|
Dual motor setup over CAN with UART by Pawel on Sun, 2018-06-17 11:50 |
5 |
by alex63610 Fri, 2019-12-27 14:27 |
VESC Firmware | |
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware on Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
Third Party Hardware | |
|
No brakes in PID Speed Control mode by karololo on Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
VESC Tool |
Pages
