You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
About motor closed loop angular velocity control by Roberto00 on Wed, 2021-04-07 02:18 |
2 |
by Offline Wed, 2021-05-05 07:57 |
Feature Requests | |
|
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline on Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
General discussion | |
|
read RPM over CAN by nblange on Mon, 2021-05-03 20:43 |
by nblange Mon, 2021-05-03 20:43 |
VESC Tool | ||
|
Question about custom coding to shutdown the motor by dsuresh on Fri, 2021-04-30 18:51 |
2 |
by dsuresh Sun, 2021-05-02 23:41 |
General discussion | |
|
VESC not reporting ah charged or wh charged by trevorjones on Sun, 2021-05-02 06:59 |
by trevorjones Sun, 2021-05-02 06:59 |
VESC Firmware | ||
|
Controlling Servo via VESC and PPM by bruchpilot123 on Wed, 2020-09-23 13:26 |
1 |
by jarryc Sun, 2021-05-02 01:25 |
General discussion | |
|
Can't download files from my account by STTrife on Sat, 2021-05-01 19:21 |
by STTrife Sat, 2021-05-01 19:21 |
General discussion | ||
|
F50-300 (Design Not Tested yet) by mrendu43 on Tue, 2021-03-09 11:49 |
13 |
by mrendu43 Sat, 2021-05-01 17:15 |
Third Party Hardware | |
|
Flipsky ADC always high by Bariiq on Fri, 2019-04-19 11:46 |
1 |
by andrecorreia Fri, 2021-04-30 01:22 |
Third Party Hardware | |
|
Why i cant insert a topic? by SafrdA on Thu, 2021-04-29 20:41 |
by SafrdA Thu, 2021-04-29 20:41 |
General discussion | ||
|
VESC 5.01 + ESP8266 + UART no data received? by i-make-robots on Wed, 2020-07-15 20:09 |
3 |
by Nickklas Tue, 2021-04-27 12:08 |
General discussion | |
|
tips for power design by antonchromjak on Mon, 2021-04-12 18:34 |
5 |
by vadicus Tue, 2021-04-27 03:01 |
Third Party Hardware | |
|
Problem with VESC Tool vs BLDC FW version by Reidar Jortveit on Mon, 2021-04-26 14:39 |
1 |
by Reidar Jortveit Mon, 2021-04-26 14:49 |
VESC Tool | |
|
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
|
VESC 75/300 R2 with R1 Firmware by frank on Thu, 2019-11-28 09:39 |
1 |
by Henque19 Sat, 2021-04-24 22:48 |
VESC Firmware | |
|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield on Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
Third Party Hardware | |
|
Is the Vesc 5 mkIII capable of 13s li-Ion (fully charged 54,6V) by Pelle on Sun, 2020-04-12 12:09 |
4 |
by danilolattaro Thu, 2021-04-22 14:50 |
General discussion | |
|
DC Motor Settings (24v PowerWheels) by KirkusMaximus on Thu, 2021-04-22 00:17 |
by KirkusMaximus Thu, 2021-04-22 00:18 |
VESC Tool | ||
|
HD60 CAN Resistor by BEWA on Wed, 2021-04-21 14:56 |
by BEWA Wed, 2021-04-21 14:56 |
VESC Original Hardware | ||
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool |
Pages
