You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Multi-turn position control with ABI encoder by vpl on Fri, 2019-02-15 13:25 |
1 |
by Gas_Sn4ke Tue, 2019-03-12 04:14 |
VESC Firmware | |
how do you arm your Vesc in arduino code? by the creator on Wed, 2019-03-13 01:11 |
by the creator Wed, 2019-03-13 01:33 |
General discussion | ||
Input Setup Wizard Does Not Ask if Single or Multi VESC by kylemuramatsu on Wed, 2019-03-13 03:22 |
1 |
by benjamin Wed, 2019-03-13 09:38 |
General discussion | |
Standard CAN Protcol by bakhrt on Sat, 2019-03-09 20:36 |
1 |
by benjamin Wed, 2019-03-13 09:54 |
VESC Firmware | |
Fault finding on failed VESC by dmcke5 on Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
General discussion | |
Fault finding on failed VESC by dmcke5 on Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
Third Party Hardware | |
Can I change control mode on the fly through the UART port? by spork on Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
General discussion | |
Update FW using vesc tool over phone by SkaterBoy58 on Thu, 2019-03-14 05:33 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
VESC Tool | ||
DRV8323 by Jessica on Thu, 2019-03-14 11:41 |
by Jessica Thu, 2019-03-14 11:42 |
General discussion | ||
Guide for modifying firmware/ apps by Enak on Wed, 2017-09-06 17:24 |
3 |
by TechAUmNu Thu, 2019-03-14 17:38 |
General discussion | |
VESC 6 DC motor Current limit? by ShortCircuit on Thu, 2019-02-07 21:56 |
14 |
by ShortCircuit Thu, 2019-03-14 19:34 |
General discussion | |
Custom Hardware - FET shoot-through problem - oscilloscope captures by ben5243 on Tue, 2019-02-19 03:58 |
2 |
by TechAUmNu Sat, 2019-03-16 00:27 |
Third Party Hardware | |
Connection over USB failed by sangious on Sun, 2019-03-17 01:20 |
by sangious Sun, 2019-03-17 01:20 |
VESC Tool | ||
Driving Issues Due To Reversed Current Amplification by F4metz on Mon, 2018-12-17 16:45 |
1 |
by moto_guy Sun, 2019-03-17 02:39 |
Third Party Hardware | |
Motion commands for controlling CNCs by andresv on Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
Feature Requests | |
Master Slave Controller for Motor by Blemot on Tue, 2019-03-19 09:46 |
by Blemot Tue, 2019-03-19 09:46 |
General discussion | ||
BEMF plot not working with VESC6 by ESCam on Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
VESC Tool | |
E vehicle setup by jordanlow on Wed, 2019-03-20 10:33 |
4 |
by jordanlow Wed, 2019-03-20 16:18 |
General discussion | |
Enhance position and rpm control interface / protocol by brushlessjoe on Wed, 2019-03-20 21:54 |
by brushlessjoe Wed, 2019-03-20 21:54 |
Feature Requests | ||
Custom App: Motor dont stop by CTSchorsch on Fri, 2019-03-22 13:43 |
by CTSchorsch Fri, 2019-03-22 13:43 |
VESC Firmware |