You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Large robot servo controller with VESC, how to set up position control by kisdia on Thu, 2024-09-19 17:47 |
by kisdia Thu, 2024-09-19 17:47 |
General discussion | ||
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule on Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
General discussion | |
|
GPIO Pins on VESC? by phils on Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
General discussion | |
|
Trying to upgrade old Enertion FOCBOX Fw 2.18 by jyl087 on Fri, 2024-09-13 16:26 |
by jyl087 Fri, 2024-09-13 17:31 |
Third Party Hardware | ||
|
REVERSE FAIL in ADC_CURRENT_REV_BUTTON_BRAKE_ADC by dk-odense on Tue, 2019-12-17 15:45 |
4 |
by Rich235 Fri, 2024-09-13 07:22 |
VESC Firmware | |
|
Dual g-foc300 setup help!!! by Re60s on Sat, 2024-09-07 09:12 |
3 |
by Tim Read Thu, 2024-09-12 16:42 |
General discussion | |
|
24 Volt LiFePO by Vaxinius on Tue, 2024-09-10 16:34 |
by Vaxinius Tue, 2024-09-10 16:35 |
General discussion | ||
|
VESC Express TCP connect with iOS not possible by johannes.b on Mon, 2024-09-02 19:51 |
2 |
by johannes.b Sat, 2024-09-07 13:56 |
General discussion | |
|
Reverse Button Status over UART? by Rich235 on Sat, 2024-09-07 10:34 |
by Rich235 Sat, 2024-09-07 10:34 |
General discussion | ||
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs on Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
General discussion | |
|
RT Data Logging CRASH by DURTYDIESEL on Sun, 2024-09-01 05:10 |
1 |
by bossski Wed, 2024-09-04 12:53 |
VESC Tool | |
|
pulsation at mid speed by smallbikefun on Sun, 2024-05-12 19:00 |
2 |
by Lizzle Wed, 2024-09-04 06:07 |
VESC Tool | |
|
Dronecan 1036.StatusExtended message for motor temp by cjmssmd on Wed, 2024-09-04 02:05 |
by cjmssmd Wed, 2024-09-04 02:05 |
Feature Requests | ||
|
RT Data crashes mobile and desktop app by Clonkex on Wed, 2022-03-02 06:42 |
3 |
by DURTYDIESEL Sun, 2024-09-01 05:17 |
VESC Tool | |
|
VESC STR-500 by eptv on Sat, 2024-01-13 07:26 |
1 |
by eptv Sat, 2024-08-31 12:36 |
VESC Original Hardware | |
|
HFI with PPM in Duty Cycle by DaganWal on Fri, 2024-08-30 00:30 |
by DaganWal Fri, 2024-08-30 00:30 |
General discussion | ||
|
Dead zone after 50% increase by simDen on Thu, 2024-08-29 19:40 |
1 |
by electricfox Thu, 2024-08-29 19:48 |
VESC Tool | |
|
speed value with geared hub motor by swampland on Tue, 2024-08-27 16:27 |
3 |
by swampland Thu, 2024-08-29 17:31 |
VESC Tool | |
|
Why only 1000 phase amp limit, and field weakening amp limits by fart on Wed, 2024-08-28 05:18 |
1 |
by electricfox Wed, 2024-08-28 13:40 |
Third Party Hardware | |
|
6.05 For IOS by NetworkDir on Tue, 2024-08-27 20:38 |
1 |
by electricfox Wed, 2024-08-28 07:14 |
VESC Tool |
Pages
