You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Wiring two VESCs by neuromancer2701 on Mon, 2018-10-01 14:42 |
2 |
by arvidb Wed, 2018-10-03 23:41 |
General discussion | |
current proportional pwm signal by grkn5434 on Mon, 2020-02-24 11:42 |
2 |
by grkn5434 Mon, 2020-02-24 15:40 |
General discussion | |
MOSFET driver delay compensation by e-biker on Sun, 2017-12-10 16:21 |
2 |
by e-biker Tue, 2017-12-12 09:41 |
General discussion | |
Real RPM=0 but ERPM>0 issue by cir7 on Tue, 2022-07-12 20:17 |
2 |
by cir7 Wed, 2022-07-13 11:43 |
General discussion | |
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto on Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
VESC Original Hardware | |
Flipsky VESC 75200 replacement parts by Matt26 on Sun, 2023-05-07 22:54 |
2 |
by david Thu, 2023-08-24 21:54 |
General discussion | |
EBike "Throttle" / "Brake" Wiring Questions by oSPANNERo on Sun, 2022-02-27 16:07 |
2 |
by oSPANNERo Mon, 2022-02-28 15:49 |
General discussion | |
"bad detection result received" impossible to achieved motor detection ! by titimomotete on Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
VESC Tool | |
Extending current shunt amplifier voltage by TechAUmNu on Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
General discussion | |
Vesc 6 and encoder connections by eptv on Thu, 2019-10-31 15:46 |
2 |
by ergnmnh Thu, 2023-12-07 13:01 |
VESC Original Hardware | |
PPM read has an offset by tuloski on Thu, 2018-09-13 09:38 |
2 |
by Stupidspencer Fri, 2019-07-19 03:09 |
VESC Tool | |
How does VESC measure the flux? by Jongwon on Thu, 2020-01-30 04:45 |
2 |
by pf26 Mon, 2020-02-10 16:18 |
General discussion | |
Sensorless tuning tips on bicycle hub motor by kalvdans on Sat, 2021-06-12 11:51 |
2 |
by neo Tue, 2021-06-15 02:02 |
General discussion | |
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... on Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
VESC Tool | |
Slow UART at high current. by memeticmusic on Thu, 2023-03-30 21:33 |
2 |
by memeticmusic Thu, 2023-04-06 11:56 |
Projects incorporating VESC technology | |
VESC6 runs at 100% throttle, but then current sense is broken by nickw1881 on Mon, 2018-09-24 06:41 |
2 |
by moto_guy Thu, 2019-03-28 06:40 |
VESC Firmware | |
Low RPM with Hoverboard hub motor by e m i l on Wed, 2020-05-13 13:06 |
2 |
by pf26 Thu, 2020-06-18 20:53 |
General discussion | |
Motor only running in reverse by obex_mike on Mon, 2018-06-25 16:25 |
2 |
by frank Tue, 2018-06-26 12:36 |
General discussion | |
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask on Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
General discussion | |
Problems with Maytech MTVESC6.12 by TheJohnson on Mon, 2020-10-19 04:50 |
2 |
by TheJohnson Wed, 2020-10-21 09:39 |
Third Party Hardware |