You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
SPI communication by CTSchorsch on Tue, 2021-03-09 22:31 |
by CTSchorsch Tue, 2021-03-09 22:31 |
VESC Firmware | ||
|
Anti-spark switch for ebikes by JR ebikes on Tue, 2021-03-09 16:31 |
by JR ebikes Tue, 2021-03-09 16:31 |
General discussion | ||
|
Lowest power/smallest available 3rd party board? by doctarr on Sun, 2021-03-07 15:28 |
4 |
by doctarr Mon, 2021-03-08 12:38 |
Third Party Hardware | |
|
throttle programing by turbomullet on Sun, 2021-03-07 22:42 |
by turbomullet Sun, 2021-03-07 22:42 |
General discussion | ||
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 on Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
VESC Tool | |
|
Been at it for like 14 hours... HALP by mnchvgs79 on Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
VESC Tool | |
|
High speed braking failure by danspratt on Wed, 2020-07-22 23:58 |
11 |
by knuthcomi Sat, 2021-03-06 23:48 |
General discussion | |
|
VESC Connections by shatty on Sat, 2021-03-06 21:49 |
by shatty Sat, 2021-03-06 21:51 |
VESC Original Hardware | ||
|
Motor-driven Haptics by frankus on Sat, 2021-03-06 04:58 |
by frankus Sat, 2021-03-06 04:58 |
Feature Requests | ||
|
vesc 3.3 or 5v is shorted to GND by fer-bo on Fri, 2021-03-05 14:57 |
1 |
by fer-bo Fri, 2021-03-05 18:24 |
VESC Original Hardware | |
|
Motor moves jerky by dsuresh on Thu, 2021-03-04 19:38 |
2 |
by dsuresh Fri, 2021-03-05 18:17 |
General discussion | |
|
using hall effect sensor for rpm detection by meisterpro on Wed, 2021-03-03 01:26 |
1 |
by vadicus Thu, 2021-03-04 18:12 |
Third Party Hardware | |
|
Problem with motor startup - only 1/2 of pole positions work in FOC by Knapers on Wed, 2021-03-03 16:51 |
by Knapers Wed, 2021-03-03 17:00 |
General discussion | ||
|
ESC blinks red when I give it input by menghaitang on Tue, 2021-03-02 21:22 |
1 |
by Knapers Wed, 2021-03-03 16:57 |
General discussion | |
|
Sporadic Duty Cycle by Patrick Donovan on Tue, 2021-03-02 01:34 |
2 |
by Patrick Donovan Tue, 2021-03-02 15:55 |
General discussion | |
|
brake inhibit input by kylerlaird on Wed, 2021-01-20 23:35 |
2 |
by isamilner Tue, 2021-03-02 09:26 |
VESC Firmware | |
|
ADC1 reads incorrect values by dsuresh on Tue, 2021-02-23 00:51 |
2 |
by dsuresh Mon, 2021-03-01 20:37 |
General discussion | |
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel on Fri, 2020-03-20 03:45 |
4 |
by TheFallen Mon, 2021-03-01 16:47 |
General discussion | |
|
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
|
Can you flash VESC Hardware with BLheli firmware? by saliraza.ai on Fri, 2021-02-26 20:38 |
1 |
by TheFallen Mon, 2021-03-01 16:31 |
VESC Original Hardware |
Pages
