You are here
Active forum topics
Primary tabs
Topic![]() |
Replies | Last post | Forum | |
---|---|---|---|---|
Реверс вращения двигателя by Wolod5 on Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
VESC Tool | |
[SOLVED]Motors "blocking totally" when throttling, after running VESC setup. by MaddiQ on Tue, 2018-06-12 21:01 |
by MaddiQ Tue, 2018-06-12 23:36 |
General discussion | ||
[Solved]Command the throttle (ADC1) with a DAC by captaintoon on Sat, 2024-01-27 23:41 |
3 |
by captaintoon Sun, 2024-01-28 15:44 |
General discussion | |
[solved] Where the motor configuration signature is from? by Beren on Thu, 2021-06-17 20:55 |
5 |
by rafeh1 Mon, 2022-11-07 00:45 |
VESC Development and Beta Testing | |
[SOLVED] VESC75/300 Poor Performance when Cold by canoeman on Tue, 2022-01-25 23:46 |
25 |
by canoeman Fri, 2022-08-12 19:13 |
VESC Original Hardware | |
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes on Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
VESC Tool | |
[SOLVED] trying to get the new release version 5.03 but when I order the free version, the linux release version doesn't show up by geoporus on Wed, 2022-06-15 10:58 |
1 |
by geoporus Wed, 2022-06-15 11:01 |
VESC Development and Beta Testing | |
[SOLVED] RPM setting not working by olivierskypullc... on Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
VESC Tool | |
[SOLVED] PWM speed control at low RPM by comes04 on Sun, 2023-04-16 13:30 |
1 |
by comes04 Wed, 2023-05-03 20:44 |
General discussion | |
[solved] Firmware 5.01 gcc compile fail.. need some insight by Bill Somerville on Tue, 2020-11-03 19:44 |
by Bill Somerville Fri, 2020-11-06 23:20 |
VESC Firmware | ||
[SOLVED] Compile vesc tool mobile apk by TZTZ on Mon, 2020-05-25 18:51 |
1 |
by TZTZ Mon, 2020-05-25 23:14 |
VESC Tool | |
[SOLVED] Can I use ADC2 for main throttle control? by oschwartz10612 on Wed, 2021-12-01 22:38 |
3 |
by oschwartz10612 Fri, 2021-12-03 05:08 |
VESC Tool | |
[Solved] Bricked VESC when trying to upload a firmware built from source by cfv-naio on Fri, 2020-08-21 16:28 |
6 |
by Bill Somerville Fri, 2020-11-06 23:18 |
VESC Development and Beta Testing | |
[SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol by yes_wecangogreen on Wed, 2023-04-12 00:51 |
1 |
by yes_wecangogreen Sat, 2023-04-29 09:24 |
General discussion | |
[OT] Increase torque on DC brush motor by Riccio on Mon, 2022-03-28 19:32 |
2 |
by Riccio Tue, 2022-03-29 09:18 |
General discussion | |
[Contributing][FOC] injected ADC and code clarity by Guillaume227 on Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
VESC Firmware | |
Your input needed: FESC 4.12 / Arduino / 4X 350W motors by matukash on Tue, 2020-07-21 16:36 |
6 |
by frank Fri, 2022-04-15 17:31 |
General discussion | |
Yet another failed connection.... by MiguelXJ on Mon, 2024-01-01 19:28 |
by MiguelXJ Mon, 2024-01-01 19:28 |
VESC Tool | ||
YAFO: Yet another FOc controler by GetItFixed on Wed, 2023-11-29 21:42 |
2 |
by GetItFixed Thu, 2024-01-04 11:05 |
Third Party Hardware | |
Xiaomi m365 mega upgrade by Tilman Baumann on Mon, 2018-02-12 12:25 |
47 |
by Grawp Wed, 2021-03-10 13:59 |
General discussion |
Pages
