You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Sticky:
Balance App Info by NuRxG on Tue, 2020-11-17 21:07 |
by NuRxG Mon, 2021-05-10 18:56 |
Balance App (for EUCs - Electric Unicycles) | ||
Experiments with high resolution sampling by talabo on Wed, 2021-11-24 17:14 |
by talabo Wed, 2021-11-24 17:14 |
Feature Requests | ||
Dual control loop with magnetic encoders by wall0069 on Sun, 2019-06-02 05:39 |
by wall0069 Sun, 2019-06-02 05:39 |
Feature Requests | ||
Bafang BBSHD hub motor setup by csev-tcejorp on Sat, 2022-08-13 14:50 |
by csev-tcejorp Sat, 2022-08-13 14:50 |
Feature Requests | ||
SINE/COSINE Encoder Support by shaman on Mon, 2018-12-17 15:14 |
10 |
by Rukus_racing Tue, 2022-06-28 02:50 |
Feature Requests | |
Total ODOMETER counter via real time logging feature request by janzobanzo7 on Mon, 2022-10-24 14:49 |
6 |
by Lennart Duijn Fri, 2023-08-11 18:38 |
Feature Requests | |
PPM with ADC by vufmihai on Mon, 2019-12-30 09:09 |
10 |
by k3ff Sat, 2024-05-11 19:09 |
Feature Requests | |
Custom Application Programming Through VESC TOOL by William Stanley on Mon, 2020-08-10 14:50 |
1 |
by William Stanley Mon, 2020-08-10 14:54 |
Feature Requests | |
Apply current to brake at low speed by argon338 on Wed, 2022-08-17 08:36 |
by argon338 Thu, 2022-08-25 17:08 |
Feature Requests | ||
DC to AC pure-sine inverter mode by shaman on Fri, 2019-10-18 15:06 |
by shaman Fri, 2019-10-18 15:06 |
Feature Requests | ||
Raw encoder output from UART by sprockmonty on Mon, 2018-08-13 16:45 |
by sprockmonty Mon, 2018-08-13 16:45 |
Feature Requests | ||
Reverse safety function by rich on Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
Feature Requests | |
Distance based on Phone GPS by Mikko Valtonen on Sat, 2020-04-25 08:33 |
by Mikko Valtonen Sat, 2020-04-25 08:38 |
Feature Requests | ||
Wheelie control by fart on Wed, 2024-04-03 10:33 |
by fart Wed, 2024-04-03 10:33 |
Feature Requests | ||
use PPM-modes with ADC by zoru24 on Mon, 2023-08-14 11:17 |
by zoru24 Mon, 2023-08-14 11:17 |
Feature Requests | ||
Read erpm of motor through motor tachometer by jordanlow on Tue, 2019-04-30 15:18 |
1 |
by Teslafly Sat, 2019-07-20 00:44 |
Feature Requests | |
Motion commands for controlling CNCs by andresv on Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
Feature Requests | |
Log ADC Feature by BITI on Mon, 2023-11-13 14:58 |
by BITI Mon, 2023-11-13 14:58 |
Feature Requests | ||
Dronecan 1036.StatusExtended message for motor temp by cjmssmd on Wed, 2024-09-04 02:05 |
by cjmssmd Wed, 2024-09-04 02:05 |
Feature Requests | ||
Lights control from the nrf remote/The WAND and configuration tab in VESC TOOL by ma-j-sterelektron on Thu, 2019-03-21 15:18 |
3 |
by ma-j-sterelektron Tue, 2020-02-18 15:00 |
Feature Requests |