You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
VESC hardware interrupt pins by gpzhao on Sun, 2018-04-01 10:47 |
by gpzhao Sun, 2018-04-01 10:50 |
VESC Firmware | ||
HD60 CAN Resistor by BEWA on Wed, 2021-04-21 14:56 |
by BEWA Wed, 2021-04-21 14:56 |
VESC Original Hardware | ||
Payment by Paypal. by ThierryGTLTS on Wed, 2017-09-06 14:38 |
by ThierryGTLTS Wed, 2017-09-06 17:50 |
General discussion | ||
Motor not running after applying SINE/COSINE settings by DHOUT on Fri, 2023-01-27 03:32 |
by DHOUT Fri, 2023-01-27 03:32 |
VESC Tool | ||
Vesc_tool running error by kwlimm on Sun, 2020-01-19 10:01 |
by kwlimm Sun, 2020-01-19 10:01 |
General discussion | ||
customer app for pwm input by ccrbs on Tue, 2020-08-11 12:06 |
by ccrbs Tue, 2020-08-11 12:06 |
General discussion | ||
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:06 |
by ruthvikchanda Thu, 2018-12-06 07:06 |
VESC Tool | ||
Maker X - SV6 - FOC Detection Issues whatever the FW by okp on Mon, 2022-07-11 12:18 |
by okp Mon, 2022-07-11 12:18 |
General discussion | ||
Connecting ABI encoder to VESC by Gas_Sn4ke on Mon, 2018-11-26 06:00 |
by Gas_Sn4ke Mon, 2018-11-26 06:00 |
VESC Tool | ||
DBC development by flatspot on Mon, 2020-11-09 08:56 |
by flatspot Mon, 2020-11-09 08:56 |
VESC Firmware | ||
Remap Rotary Encoder Input to CAN (or other) by Artemis Skade on Wed, 2020-04-01 20:23 |
by Artemis Skade Wed, 2020-04-01 20:23 |
Feature Requests | ||
Enhance position and rpm control interface / protocol by brushlessjoe on Wed, 2019-03-20 21:54 |
by brushlessjoe Wed, 2019-03-20 21:54 |
Feature Requests | ||
Adding Openloop Com Comand and Temp. Measurement via Resistance by JulianT on Mon, 2022-10-03 11:32 |
by JulianT Mon, 2022-10-03 11:32 |
Feature Requests | ||
Newer DRV8353RS instead of DRV8301? by whydoilive on Fri, 2021-04-02 10:13 |
by whydoilive Fri, 2021-04-02 10:13 |
VESC6 Beta | ||
burnend vesc6 mk3 by sandmen on Mon, 2020-08-17 11:48 |
by sandmen Mon, 2020-08-17 11:48 |
VESC Original Hardware | ||
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
Thread safety issues when using both serial and USB communication together by vadimz on Sun, 2018-12-23 16:32 |
by vadimz Sun, 2018-12-23 16:32 |
VESC Firmware | ||
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool |
Pages
