You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
DC Motor Settings (24v PowerWheels) by KirkusMaximus on Thu, 2021-04-22 00:17 |
by KirkusMaximus Thu, 2021-04-22 00:18 |
VESC Tool | ||
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool | ||
|
throttle mapping: non-zero current at zero adc input? by FreddyForLaunch on Wed, 2021-04-14 21:48 |
by FreddyForLaunch Thu, 2021-04-15 09:00 |
VESC Tool | ||
|
Pc requirement to run vesc software by proget.snc on Mon, 2021-04-12 10:57 |
1 |
by benjamin Wed, 2021-04-14 19:47 |
VESC Tool | |
|
Questions on VESC tool by da_rul0r on Wed, 2019-08-14 09:47 |
5 |
by Isi Mon, 2021-04-12 17:34 |
VESC Tool | |
|
Get data from VESC on Arduino by jhanvisharma on Wed, 2021-04-07 08:25 |
1 |
by CTSchorsch Wed, 2021-04-07 09:05 |
VESC Tool | |
|
VESC failure presumably due to current oscillations at high current by rsarver on Wed, 2021-03-24 22:06 |
by rsarver Wed, 2021-03-24 22:06 |
VESC Tool | ||
|
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
|
Data logging by charper on Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
VESC Tool | |
|
D vs omega control by rsarver on Wed, 2021-03-17 14:44 |
by rsarver Wed, 2021-03-17 14:44 |
VESC Tool | ||
|
motor stops spinning on its own by rsarver on Tue, 2021-03-16 16:30 |
1 |
by rsarver Tue, 2021-03-16 22:13 |
VESC Tool | |
|
Battery Voltage Settings by huffauden19 on Wed, 2020-03-04 23:17 |
2 |
by laser30 Sat, 2021-03-13 16:57 |
VESC Tool | |
|
Update fail from FW3.58 to 3.61 by sachs2019 on Tue, 2019-09-10 15:51 |
7 |
by AlmaRaposa Thu, 2021-03-11 17:44 |
VESC Tool | |
|
I Mac Vesc tool !!!! by PHATTY on Fri, 2019-10-11 17:56 |
2 |
by Bender Wed, 2021-03-10 14:39 |
VESC Tool | |
|
Throttle and Brake by shatty on Wed, 2021-03-10 01:19 |
by shatty Wed, 2021-03-10 01:22 |
VESC Tool | ||
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 on Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
VESC Tool | |
|
Been at it for like 14 hours... HALP by mnchvgs79 on Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
VESC Tool | |
|
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
|
MAX ERPM by riderman on Sun, 2021-02-28 23:05 |
by riderman Sun, 2021-02-28 23:05 |
VESC Tool | ||
|
RPM increase by Tibor Kalman Za... on Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
VESC Tool |
Pages
