You are here

VESC Firmware

Topic / Topic starter Replies Last postsort ascending
Normal topic Dual Vesc reading second wheel RPM
by rdavenport3 » Tue, 2022-05-03 15:32
0
by rdavenport3
Tue, 2022-05-03 15:32
Normal topic position hold below specific duty cycle
by lacondro » Wed, 2022-04-27 04:41
1
by lacondro
Wed, 2022-04-27 10:44
Normal topic CAN sends error frame
by dgarciasoto » Wed, 2022-04-27 07:11
0
by dgarciasoto
Wed, 2022-04-27 07:11
Normal topic App development and Debug
by dpeinado » Fri, 2022-04-01 13:22
1
by Gatze
Sun, 2022-04-24 00:15
Normal topic how to download v5.03 firmware?
by barncat08 » Wed, 2022-01-26 18:35
4
by Gatze
Sat, 2022-04-23 11:48
Normal topic Max thread rate for simple app?
by clazarowitz » Wed, 2022-04-20 04:34
0
by clazarowitz
Wed, 2022-04-20 04:34
Normal topic Cannot read data over UART
by amalbers01 » Sat, 2022-04-16 05:03
1
by frank
Sat, 2022-04-16 20:06
Normal topic Problem with BLDC motor direction and code starting sequence.
by masifsr » Fri, 2022-04-15 12:37
0
by masifsr
Fri, 2022-04-15 12:37
Normal topic Porting to a newer STM32
by TechAUmNu » Wed, 2020-09-16 12:38
4
by STEPHY AKKARA
Thu, 2022-04-14 07:57
Normal topic Requesting VESC fault codes via UART
by spork » Fri, 2020-06-26 21:52
1
by f.damien12
Sun, 2022-04-03 18:27
Normal topic Write motor configuration from XML file in 3rd app
by jernejm » Tue, 2022-03-29 11:56
0
by jernejm
Tue, 2022-03-29 11:56
Normal topic Sending Negative Values to VESC over CAN bus
by olivierabristol » Fri, 2022-03-25 09:11
0
by olivierabristol
Fri, 2022-03-25 09:13
Normal topic Firmware update for mac needed.
by RustyHook » Wed, 2022-03-16 17:50
2
by RustyHook
Wed, 2022-03-16 17:54
Normal topic VESC firmware to programmable Sabvoton ml60 controller.
by Maciejwarloch » Tue, 2022-03-08 13:25
0
by Maciejwarloch
Tue, 2022-03-08 13:25
Normal topic Where to find codelines for speed and position control structure
by kianK » Tue, 2022-03-01 15:25
0
by kianK
Thu, 2022-03-03 12:23
Normal topic Get Current over CAN bus
by chriswei » Thu, 2019-05-16 13:57
4
by spacewalker
Mon, 2022-02-21 08:25
Normal topic mcpwm_set_current VS mcpwm_set_brake_current
by stiganielsen » Wed, 2019-09-11 15:40
2
by mechhead
Mon, 2022-02-14 11:04
Normal topic VESC with propeller, not reaching max performance
by ogent » Tue, 2022-02-01 16:31
8
by ogent
Thu, 2022-02-03 14:54
Normal topic Loss of control during regen
by mckenzie.keith » Fri, 2022-01-28 02:42
3
by frank
Sat, 2022-01-29 10:34
Normal topic The engine stopped spinning after updating firmware
This topic has been moved to "VESC Tool" (View topic)
Normal topic new vesc 6 FW update
by Shwepsss » Thu, 2022-01-20 20:26
1
by Shwepsss
Fri, 2022-01-21 15:20
Normal topic PAS app: limit current depending on actual velocity
by dpeinado » Fri, 2022-01-21 13:49
0
by dpeinado
Fri, 2022-01-21 13:49
Normal topic Stream UART Telemetry without a Request
by AlexBenn » Thu, 2022-01-20 02:47
0
by AlexBenn
Thu, 2022-01-20 02:47
Normal topic firm ware error 75_300
by yuri12 » Wed, 2022-01-19 09:50
1
by frank
Wed, 2022-01-19 13:46
Normal topic ESC FS75100
by myck33 » Fri, 2021-12-31 14:17
2
by jaykup
Sun, 2022-01-16 22:43
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Firmware