You are here
VESC Firmware
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Get Current over CAN bus by chriswei » Thu, 2019-05-16 13:57 |
4 |
by spacewalker Mon, 2022-02-21 08:25 |
|
mcpwm_set_current VS mcpwm_set_brake_current by stiganielsen » Wed, 2019-09-11 15:40 |
2 |
by mechhead Mon, 2022-02-14 11:04 |
|
VESC with propeller, not reaching max performance by ogent » Tue, 2022-02-01 16:31 |
8 |
by ogent Thu, 2022-02-03 14:54 |
|
Loss of control during regen by mckenzie.keith » Fri, 2022-01-28 02:42 |
3 |
by frank Sat, 2022-01-29 10:34 |
|
The engine stopped spinning after updating firmware This topic has been moved to "VESC Tool" (View topic) |
|||
new vesc 6 FW update by Shwepsss » Thu, 2022-01-20 20:26 |
1 |
by Shwepsss Fri, 2022-01-21 15:20 |
|
PAS app: limit current depending on actual velocity by dpeinado » Fri, 2022-01-21 13:49 |
0 |
by dpeinado Fri, 2022-01-21 13:49 |
|
Stream UART Telemetry without a Request by AlexBenn » Thu, 2022-01-20 02:47 |
0 |
by AlexBenn Thu, 2022-01-20 02:47 |
|
firm ware error 75_300 by yuri12 » Wed, 2022-01-19 09:50 |
1 |
by frank Wed, 2022-01-19 13:46 |
|
ESC FS75100 by myck33 » Fri, 2021-12-31 14:17 |
2 |
by jaykup Sun, 2022-01-16 22:43 |
|
BLDC_SPEED_CONTROL_CURRENT by salviador » Fri, 2022-01-14 16:32 |
0 |
by salviador Fri, 2022-01-14 16:32 |
|
high side active low and low side active high driver signal setting in firmware. by Spencer.chen » Wed, 2021-12-15 14:00 |
0 |
by Spencer.chen Wed, 2021-12-15 14:04 |
|
Can't seem to downgrade firmware on my VESC 6 MKV by curiousgeorge » Thu, 2021-12-02 08:46 |
4 |
by curiousgeorge Fri, 2021-12-03 19:00 |
|
Right hardware for FW:60 and FSESC6.6 by alexantosh » Wed, 2021-12-01 19:40 |
0 |
by alexantosh Wed, 2021-12-01 20:19 |
|
Flipsky ESC 6.6 - How to Compile? [fixed] by hoeken » Tue, 2021-08-31 03:33 |
3 |
by alexantosh Wed, 2021-12-01 18:55 |
|
Compiled Firmware 5.02 does not work by sirAnton » Wed, 2021-01-27 08:19 |
10 |
by alexantosh Wed, 2021-12-01 18:53 |
|
Importance of the MK version and Determining the MK version of the VESC by alexantosh » Tue, 2021-11-23 12:15 |
9 |
by alexantosh Tue, 2021-11-30 13:58 |
|
Wand firmware 1.3 by peacue » Mon, 2021-11-22 09:59 |
1 |
by frank Mon, 2021-11-22 12:56 |
|
Control System of VESC by mm_iem » Wed, 2021-08-25 14:52 |
2 |
by kubark42 Wed, 2021-11-17 16:59 |
|
Urgent VESC Firmware Issue by D1200 » Tue, 2021-11-16 02:32 |
2 |
by frank Tue, 2021-11-16 09:50 |
|
How difficult would it be to add code to read an external EEPROM, and deactivate/activate depending on a value by PaulMakesThings » Thu, 2021-11-11 09:55 |
0 |
by PaulMakesThings Thu, 2021-11-11 09:55 |
|
how to build new bin code on win10 by yiannis » Wed, 2021-09-15 21:05 |
1 |
by skyline1970 Fri, 2021-10-29 11:54 |
|
Which firmware do I need by Luka-Zagar » Tue, 2021-10-19 22:24 |
2 |
by Luka-Zagar Wed, 2021-10-20 19:38 |
|
Green LED on older VESC, v4.12? by smith2e7 » Mon, 2021-10-18 17:42 |
0 |
by smith2e7 Mon, 2021-10-18 17:42 |
|
The connected VESC has test firmware, and this is not a test build of VESC Tool. You should update the firmware urgently, as thi by Thomas W Donohue » Sat, 2021-07-17 14:26 |
3 |
by frank Tue, 2021-10-12 20:47 |
Log in to post new content in the forum.