You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Flipsky6.6 usb not detected This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy » Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
|
|
Current sensor and commanded current by galp » Fri, 2019-02-22 23:08 |
0 |
by galp Fri, 2019-02-22 23:08 |
|
|
VESC on DIY CNC router by tbartoletta » Wed, 2019-02-20 03:00 |
5 |
by GunnarW Thu, 2019-02-21 16:44 |
|
|
VESC Questions from the newbie by mendez » Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
|
|
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 » Sun, 2019-02-17 19:20 |
0 |
by Syl2078 Sun, 2019-02-17 19:20 |
|
|
Observer tracking fail by dangminhducnbk » Sun, 2019-02-17 14:09 |
0 |
by dangminhducnbk Sun, 2019-02-17 14:09 |
|
|
Struggling in startup BLDC in sensorless mode by dangminhducnbk » Fri, 2019-02-15 03:42 |
2 |
by dangminhducnbk Sun, 2019-02-17 12:48 |
|
|
2 vs 3 phase shunts by antonchromjak » Sun, 2018-04-15 13:25 |
13 |
by TechAUmNu Fri, 2019-02-15 18:57 |
|
|
No connection with vesc by Matthieu van Ra... » Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
|
|
Building the vesc firmware in Chibi Studio by chris1seto » Sat, 2019-01-12 02:36 |
1 |
by kinzma Thu, 2019-02-14 09:42 |
|
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 » Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
|
|
Sub zero temperature VESC412 issues by jetigm » Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
|
|
Dual brushed motors from 1 R/C stick? by VESC1 » Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
|
|
Fault:DRV8302 DUAL V4 by Lzx19961014 » Tue, 2018-09-04 11:48 |
3 |
by stone_1706 Sat, 2019-02-02 17:09 |
|
|
VESC Tool Instructions by brschaefer74 » Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
|
|
VESC and Motors for sale. by raess » Thu, 2019-01-24 22:41 |
0 |
by raess Thu, 2019-01-24 22:41 |
|
|
Connect both hall and incremental quadrature encoders by vpl » Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
|
|
Increasing low rpm torque in FOC mode by galp » Mon, 2019-01-21 18:15 |
1 |
by sam.vanratt Thu, 2019-01-24 00:02 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
|
Change RPM of motor by Gas_Sn4ke » Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
|
|
Vesc 6 motor setup fault by Davo69URX » Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
|
|
Upload bootloader to new MCU by Jessica » Fri, 2019-01-11 14:43 |
7 |
by Jessica Wed, 2019-01-16 09:07 |
|
|
4kw BLDC hybrid system help by thardi10 » Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
|
Log in to post new content in the forum.
