You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 6 hi voltage problem by mike » Fri, 2018-05-04 11:34 |
4 |
by mike Tue, 2018-05-08 19:31 |
|
|
Rolling down-hill faster than my board's electric top speed by koralle » Tue, 2018-05-01 21:18 |
4 |
by koralle Sun, 2018-05-06 18:25 |
|
|
Forum broken. by Roger Wolff » Thu, 2018-05-03 08:31 |
3 |
by Tilman Baumann Fri, 2018-05-04 13:01 |
|
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
|
|
Need help: Motor spins in sensorless mode, but not in sensored mode by acu192 » Sun, 2018-04-29 20:23 |
3 |
by acu192 Mon, 2018-04-30 01:05 |
|
|
vesc6 limitations by badger1666 » Sat, 2018-04-28 19:20 |
0 |
by badger1666 Sat, 2018-04-28 19:20 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
|
|
The motor with an enkoder of AS5048 rotates unevenly by densor » Thu, 2018-04-26 11:41 |
2 |
by densor Fri, 2018-04-27 08:27 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
|
|
Duty vs RPM for smooth start and slow running by Davideo » Tue, 2018-04-24 14:42 |
0 |
by Davideo Tue, 2018-04-24 14:42 |
|
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 » Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
|
|
Brakes completely repeatedly failing at high temperature by Paul15578 » Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
|
|
Firmware update thru UART? by cromoly » Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
|
|
can't reach the maximum speed by kingpon » Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
|
|
Extending current shunt amplifier voltage by TechAUmNu » Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
|
|
Hall sensor filter on VESC flier board by raess » Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
|
|
Motor temperature increase by e-biker » Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
|
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker » Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
|
|
Potentiometer control by khadra.m123 » Thu, 2018-04-05 08:51 |
3 |
by slapshot136 Sun, 2018-04-08 00:07 |
|
|
acceleration speed and temp noise by badger1666 » Wed, 2018-04-04 20:18 |
5 |
by badger1666 Fri, 2018-04-06 20:13 |
|
|
Timeout Brake Current [Fail Save] by Cuprani » Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
|
|
vesc6 help me learn by badger1666 » Sat, 2018-03-31 09:05 |
2 |
by badger1666 Mon, 2018-04-02 20:15 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
Can motor parameters be detected with shaft load? by powerlabor001 » Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
|
|
Which encoders are supported? by raess » Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
Log in to post new content in the forum.
