You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
HArd power off switch by jakaranda » Mon, 2018-10-29 11:15 |
3 |
by sam.vanratt Sat, 2018-11-24 18:08 |
|
|
USB can not recognize by xiaofeixiak » Sat, 2018-11-24 03:20 |
1 |
by sam.vanratt Sat, 2018-11-24 14:44 |
|
|
Encoder over SPI doesn't work on FW3.40: SOLVED by john » Mon, 2018-11-12 09:00 |
2 |
by john Fri, 2018-11-23 16:40 |
|
|
LED HW PWM?? by milom » Fri, 2018-11-16 15:29 |
1 |
by benjamin Fri, 2018-11-23 09:57 |
|
|
Fried Hall Effect Throttle Sensor by cdw3423vesc » Thu, 2018-11-15 05:16 |
2 |
by sam.vanratt Thu, 2018-11-22 20:33 |
|
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist » Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
|
|
Noise between VESC and microcontroller by onsokumaru » Tue, 2018-04-03 21:56 |
2 |
by fourchette Tue, 2018-11-20 21:32 |
|
|
enertionboard focbox : is vesc_tool safe to use? by fourchette » Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
|
|
where to source BLDC 6.5in geared wheel? by fourchette » Thu, 2018-11-08 00:05 |
3 |
by fourchette Mon, 2018-11-19 22:54 |
|
|
Best way to stop "de-sync" of motors by Paul15578 » Tue, 2017-12-05 04:57 |
11 |
by Dillon Mon, 2018-11-19 02:11 |
|
|
Set and measure RPM - Questions by Piep » Thu, 2018-11-08 16:10 |
0 |
by Piep Thu, 2018-11-08 16:10 |
|
|
dual vesc question by badger1666 » Sun, 2018-10-28 12:59 |
0 |
by badger1666 Sun, 2018-10-28 12:59 |
|
|
PPM valure seems wrong by KKKim » Tue, 2018-10-23 10:56 |
1 |
by frank Fri, 2018-10-26 17:29 |
|
|
FOC Calibration over CAN by thisisjaye » Fri, 2018-10-26 13:15 |
1 |
by frank Fri, 2018-10-26 17:12 |
|
|
Vesc is not working by Patryk » Mon, 2018-10-08 18:48 |
4 |
by Patryk Fri, 2018-10-19 22:25 |
|
|
ackmaniac app stopped working ? by badger1666 » Sat, 2018-10-13 12:36 |
1 |
by portnawake Wed, 2018-10-17 08:34 |
|
|
Position Control with Resolver by robo_studienarbeit » Tue, 2018-10-16 18:57 |
0 |
by robo_studienarbeit Tue, 2018-10-16 18:57 |
|
|
Help with translating/converting hall sensor values from BLDC to FOC by theviith » Thu, 2018-10-11 09:47 |
0 |
by theviith Thu, 2018-10-11 09:47 |
|
|
VESC for small drone (<1kg) by iKrosoft » Wed, 2018-10-03 16:40 |
3 |
by arvidb Thu, 2018-10-04 21:05 |
|
|
Wiring two VESCs by neuromancer2701 » Mon, 2018-10-01 14:42 |
2 |
by arvidb Wed, 2018-10-03 23:41 |
|
|
Switch two Motor Profiles/Modes (UART) by anli » Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
|
|
dual vesc by badger1666 » Fri, 2018-09-21 09:10 |
4 |
by badger1666 Sat, 2018-09-29 15:45 |
|
|
Compiling in a different config. by Roger Wolff » Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
|
|
Speed control tuning for 500-1000 RPM by vadimz » Sun, 2018-09-02 18:09 |
2 |
by vadimz Sat, 2018-09-15 14:08 |
|
|
FAULT_CODE_DRV Motor not spinning by Mightyorc » Sat, 2018-09-15 03:36 |
0 |
by Mightyorc Sat, 2018-09-15 03:36 |
Log in to post new content in the forum.
