You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Observer tracking fail by dangminhducnbk » Sun, 2019-02-17 14:09 |
0 |
by dangminhducnbk Sun, 2019-02-17 14:09 |
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
Changing the timer for VESC auto turn off timing by dsuresh » Mon, 2021-03-15 21:19 |
0 |
by dsuresh Mon, 2021-03-15 21:19 |
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
Flipsky6.6 usb not detected This topic has been moved to "Third Party Hardware" (View topic) |
|||
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
Hi by elsie » Thu, 2018-01-25 02:49 |
0 |
by elsie Thu, 2018-01-25 16:23 |
|
4.12 cooling mod by thewho » Wed, 2019-05-01 18:45 |
0 |
by thewho Wed, 2019-05-01 18:45 |
|
Can someone verify this by jsbenson » Mon, 2023-06-26 09:22 |
0 |
by jsbenson Tue, 2023-06-27 07:50 |
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
Interessante Arbeiten zum Thema eSkateboard by barney » Tue, 2017-01-03 18:55 |
0 |
by barney Tue, 2017-01-03 18:55 |
|
VESC 6: frequent direction change application problem by cromoly » Thu, 2019-05-02 01:45 |
0 |
by cromoly Thu, 2019-05-02 01:45 |
|
Motors spin during detection but then won't spin by jsbenson » Tue, 2023-06-27 23:54 |
0 |
by jsbenson Tue, 2023-06-27 23:54 |
|
Minimum speed push cart using arduino by BarBumble » Wed, 2021-05-12 09:29 |
0 |
by BarBumble Wed, 2021-05-12 09:29 |
|
VESC6 cooked MOSFET by hagoston » Mon, 2021-03-22 14:23 |
0 |
by hagoston Mon, 2021-03-22 15:03 |
|
RPM Control Problems by MrMonk3y » Mon, 2019-05-06 22:54 |
0 |
by MrMonk3y Mon, 2019-05-06 22:54 |
|
12v(3s) Input to VESC 75/250 by AliBarrett10 » Wed, 2021-03-24 14:36 |
0 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
|
Bench Testing by usaevo7 » Tue, 2023-04-25 16:50 |
0 |
by usaevo7 Tue, 2023-04-25 16:50 |
|
120V dual VESC for E-scooter by Daniel Kaminski » Sun, 2021-03-28 12:43 |
0 |
by Daniel Kaminski Sun, 2021-03-28 12:43 |
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
Log in to post new content in the forum.