You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Flipsky screen for Ubox driver help! by Dostawca.L » Sat, 2025-02-22 19:20 |
0 |
by Dostawca.L Sat, 2025-02-22 19:20 |
|
|
Motor compatibility (and power levels) by MrSurly » Tue, 2022-04-12 21:43 |
0 |
by MrSurly Tue, 2022-04-12 21:43 |
|
|
vesc 75100 variations for a kart build by elbracer » Mon, 2025-05-19 19:57 |
0 |
by elbracer Mon, 2025-05-19 19:57 |
|
|
"Throttle" help by benha » Wed, 2019-08-07 05:58 |
0 |
by benha Wed, 2019-08-07 05:58 |
|
|
Servo output CAN Formats by vinci » Mon, 2022-04-18 15:35 |
0 |
by vinci Mon, 2022-04-18 15:35 |
|
|
Updated firmware on duel hd60 now one wont turn on by Hippydeathcult » Thu, 2025-02-27 11:10 |
0 |
by Hippydeathcult Thu, 2025-02-27 11:10 |
|
|
Motor detection failed by DragosZapodeanu » Tue, 2022-04-19 15:09 |
0 |
by DragosZapodeanu Tue, 2022-04-19 15:09 |
|
|
bldc motor calibration issue by Thejesh Bollineni » Sat, 2025-03-01 00:15 |
0 |
by Thejesh Bollineni Sat, 2025-03-01 00:15 |
|
|
75300 make high pitch after close power switch by Kaeomangkon » Sat, 2025-03-08 11:37 |
0 |
by Kaeomangkon Sat, 2025-03-08 11:37 |
|
|
Switch between pre-defined profiles over UART by PutridFox » Sun, 2025-06-15 13:11 |
0 |
by PutridFox Sun, 2025-06-15 13:11 |
|
|
Simulating controller accurately by TechAUmNu » Fri, 2019-08-16 15:35 |
0 |
by TechAUmNu Fri, 2019-08-16 15:35 |
|
|
Help with understanding/using PID control by Groundspeed100 » Tue, 2025-03-11 15:58 |
0 |
by Groundspeed100 Tue, 2025-03-11 16:01 |
|
|
Bluetooth module in VESC 75/300 by Hermann Schnaeuzle » Fri, 2022-04-22 17:55 |
0 |
by Hermann Schnaeuzle Fri, 2022-04-22 17:55 |
|
|
Active braking without regen current by stoibinger » Mon, 2025-03-17 14:17 |
0 |
by stoibinger Mon, 2025-03-17 14:17 |
|
|
foc with encoder fails to run smoothly by jdn » Thu, 2019-08-22 12:26 |
0 |
by jdn Thu, 2019-08-22 15:47 |
|
|
Designing a robust power stage using Mosfets by ripperpc » Tue, 2020-05-05 08:04 |
0 |
by ripperpc Tue, 2020-05-05 08:04 |
|
|
VESC Express GPS Logging frequency by steveeng » Tue, 2025-03-25 22:55 |
0 |
by steveeng Tue, 2025-03-25 22:55 |
|
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh » Tue, 2022-03-22 15:32 |
0 |
by mouadh Tue, 2022-03-22 17:38 |
|
|
Wolf king 11 gt 72v perimeters Help by jsherbz92 » Tue, 2025-04-01 05:52 |
0 |
by jsherbz92 Tue, 2025-04-01 05:52 |
|
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li » Fri, 2019-07-05 06:55 |
0 |
by Jack_Li Fri, 2019-07-05 06:58 |
|
|
What motors can i use with the vesc? by bengce » Sun, 2020-06-14 22:28 |
0 |
by bengce Sun, 2020-06-14 22:28 |
|
|
Reverse and brake inputs? by hackish » Sat, 2019-09-07 19:20 |
0 |
by hackish Sat, 2019-09-07 19:20 |
|
|
Remote pairs but motor does not spin after VESC tool use by frunobulax » Fri, 2025-04-11 18:26 |
0 |
by frunobulax Fri, 2025-04-11 18:26 |
|
|
Flipsky 75100 + tft screen by omrishalev123 » Mon, 2024-12-30 23:10 |
0 |
by omrishalev123 Mon, 2024-12-30 23:10 |
|
|
Voltage on motor leads @ 0 throttle by SimpleUnmanned » Thu, 2020-05-21 02:40 |
0 |
by SimpleUnmanned Thu, 2020-05-21 02:40 |
Log in to post new content in the forum.
