You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Limit Max RPM on a Brushed Motor in DC Mode by KirkusMaximus » Fri, 2020-09-04 02:52 |
0 |
by KirkusMaximus Fri, 2020-09-04 02:58 |
|
|
Reprogram VESC for sensorless motor by Christopherinco... » Thu, 2020-09-03 00:10 |
2 |
by vadicus Thu, 2020-09-03 01:14 |
|
|
Ebike specific code ? by flix » Wed, 2019-08-14 21:43 |
4 |
by vadicus Thu, 2020-08-27 19:08 |
|
|
FOC current oscillation at max. speed by ProgramThyself » Mon, 2020-08-10 05:55 |
10 |
by SRFirefox Wed, 2020-08-26 23:10 |
|
|
Dual VESC, Dual UART? by kneave » Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
|
|
Controlling general BLDC motors by sinned6915 » Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
|
|
VESC Tool Android pairinglist reset with metr.at by nice2cu » Sun, 2020-08-23 12:24 |
0 |
by nice2cu Sun, 2020-08-23 12:24 |
|
|
Auxiliary Output Mode pin# by garyp » Sat, 2020-08-22 18:17 |
0 |
by garyp Sat, 2020-08-22 18:17 |
|
|
Paragliding rewinder control loop by eptv » Mon, 2019-11-04 08:20 |
1 |
by rookieatbest Fri, 2020-08-21 03:30 |
|
|
Foc limit at 25v by Thegolfer » Wed, 2020-08-19 18:51 |
1 |
by Thegolfer Wed, 2020-08-19 19:56 |
|
|
Can't connect to VESC's? Linux, need help? by ex-Gooserider » Wed, 2020-08-12 04:38 |
4 |
by ex-Gooserider Wed, 2020-08-19 01:39 |
|
|
Battery power by bryncjones » Mon, 2020-08-17 15:35 |
2 |
by TheFallen Tue, 2020-08-18 11:46 |
|
|
Hardware fault troubleshooting by thewho » Sat, 2020-08-15 16:50 |
2 |
by thewho Tue, 2020-08-18 00:07 |
|
|
VESC with really high KV by bengce » Sun, 2020-06-21 11:18 |
18 |
by bengce Thu, 2020-08-13 14:11 |
|
|
My VESC TOOL did not have "balance" by Elijah K » Wed, 2020-08-12 07:52 |
0 |
by Elijah K Wed, 2020-08-12 07:53 |
|
|
Vesc Suddenly stopped working by Erik » Wed, 2020-08-05 14:53 |
6 |
by Erik Tue, 2020-08-11 20:59 |
|
|
Hub Motor Gives up while Coasting With No Faults by vadicus » Sun, 2020-08-09 01:36 |
4 |
by vadicus Tue, 2020-08-11 18:01 |
|
|
customer app for pwm input by ccrbs » Tue, 2020-08-11 12:06 |
0 |
by ccrbs Tue, 2020-08-11 12:06 |
|
|
VESC behaviour as constant torque winch by devmonkey » Thu, 2020-07-09 23:43 |
4 |
by district9prawn Mon, 2020-08-10 13:21 |
|
|
Controlled decend speed on long downhill by sjgan68 » Sun, 2020-08-09 11:38 |
1 |
by vadicus Sun, 2020-08-09 20:49 |
|
|
Upload bootloader to stm32 f405? by jneumann » Sat, 2020-08-08 07:11 |
3 |
by TechAUmNu Sat, 2020-08-08 18:29 |
|
|
VESC Input Using Raspberry Pi and Wiimote by Schizug » Wed, 2019-03-27 04:28 |
3 |
by Nelf Sat, 2020-08-08 01:13 |
|
|
Control a 3 phase linear induction motor with vesc by Choocie » Wed, 2020-08-05 14:19 |
1 |
by TheFallen Thu, 2020-08-06 23:56 |
|
|
Rough transition to sensorless under load by vadicus » Sat, 2020-07-18 07:10 |
5 |
by vadicus Wed, 2020-08-05 20:10 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
Log in to post new content in the forum.
