You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
High voltage vesc 75/250 Field Weakening by reubarb.scons » Wed, 2022-03-02 08:45 |
2 |
by reubarb.scons Tue, 2022-03-15 07:14 |
|
|
VESC not responding to throttle by posthy » Thu, 2022-03-10 17:12 |
1 |
by skyline1970 Mon, 2022-03-14 20:37 |
|
|
Torque Ramp Rate whilst in FOC by J_W97 » Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
|
|
VESC HD60T CAN DUTY CYCLE CONTROL by v1n23nt » Thu, 2022-02-17 09:39 |
2 |
by v1n23nt Mon, 2022-03-14 16:54 |
|
|
Does VESC reduce/disable regen braking based on battery voltage? by rorosaurus » Tue, 2020-08-11 23:20 |
11 |
by J_W97 Mon, 2022-03-14 14:43 |
|
|
Powering a Custom Motor With Large Air Gap by magma » Mon, 2022-01-24 23:38 |
1 |
by skyline1970 Mon, 2022-03-14 09:56 |
|
|
Controlling a custom made RC Vehicle by Skaaly » Sat, 2022-03-05 12:56 |
1 |
by skyline1970 Mon, 2022-03-14 09:16 |
|
|
Cannot downgrade from 5.03 to 5.02 by kallep » Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
|
|
Connecting handlebar controlls by mannberg » Thu, 2022-03-10 14:57 |
0 |
by mannberg Thu, 2022-03-10 14:57 |
|
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 14:19 |
0 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
|
|
Flipsky 75100 controller not producing the same amount of power as esc controller at same current by Ashton » Mon, 2021-12-06 21:18 |
2 |
by Liam Li Sun, 2022-03-06 20:31 |
|
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin » Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
|
|
VESC100/250; RPM Pulse input; antispark precharge by tobiokanobi » Mon, 2022-02-28 11:56 |
7 |
by tobiokanobi Thu, 2022-03-03 11:22 |
|
|
Best Throttle and break level by ardillolambo » Wed, 2022-03-02 18:29 |
0 |
by ardillolambo Wed, 2022-03-02 18:29 |
|
|
Emergency Stop SSR - Blowing up Microcontroller by J_W97 » Tue, 2022-03-01 14:46 |
5 |
by frank Tue, 2022-03-01 20:19 |
|
|
When SWD Program Connect Fails by canoeman » Mon, 2022-02-28 18:32 |
0 |
by canoeman Mon, 2022-02-28 18:32 |
|
|
Can't receive status message via CAN bus by IanG » Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
|
|
Dissimilar motor testing by geofrancis » Thu, 2022-02-24 16:54 |
0 |
by geofrancis Thu, 2022-02-24 16:57 |
|
|
hysteresis related issue in mcconf and mcpwm_foc.c by masifsr » Thu, 2022-02-24 13:14 |
1 |
by j.konrad Thu, 2022-02-24 14:52 |
|
|
VESC for electric scooter by eyup » Tue, 2022-02-22 13:52 |
1 |
by Filip Kinl Thu, 2022-02-24 13:35 |
|
|
Difference between ERPM and Duty Cycle by dormanae » Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
|
|
Why use sensorless if the motor has sensors? by j.konrad » Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
|
|
ADC EBike Throttle Not Responding by d_hoody » Thu, 2018-12-13 02:04 |
11 |
by Oded Mazor Sat, 2022-02-19 07:41 |
|
|
will VESC synch with a 1020 inrunner? by Oded Mazor » Fri, 2022-02-18 16:58 |
1 |
by frank Fri, 2022-02-18 17:51 |
|
|
FOC motor just grinds on speed command, spins up smoothly during parameter calibration by mmiles19 » Wed, 2022-02-16 23:21 |
1 |
by frank Thu, 2022-02-17 07:32 |
Log in to post new content in the forum.
